HP 3C590-TPO Manual do Utilizador

Etherlink III PCI Network Interface Card (10BT)3C590-TPOInstallation Guide

2 Connecting to a Netware 4.11 ServerWindows for Workgroups4 Select “CONFIGURE NIC,” and verify the resource settings listed above under the heading “

2 Connecting to a Netware 4.11 ServerWindows for Workgroups8 Accept the default products by pressing Enter, and then press “F10” to continue.9 Select

2 Connecting to a Netware 4.11 ServerWindows for Workgroups

2 Connecting to a Netware 4.11 ServerWindows 95 SR2Windows 95 SR2 Requirements• HP Vectra with Windows 95 SR2 installed.• 3COM Etherlink 3C509-B ethe

2 Connecting to a Netware 4.11 ServerWindows 95 SR28 When prompted, click on “OK” to continue.9 Enter “Computer Name”, “Workgroup”, and “Computer Des

3 Connecting to a Windows NT Server 3.51Windows for Workgroups Ver. 3.113 Connecting to a Windows NT Server 3.51Windows for Workgroups Ver. 3.11Requi

3 Connecting to a Windows NT Server 3.51Windows for Workgroups Ver. 3.118 After windows loads, open the “NETWORK” program group, and double-click on “

3 Connecting to a Windows NT Server 3.51Windows for Workgroups Ver. 3.1122 To complete the installation, click on “Restart Computer” in the “Windows

3 Connecting to a Windows NT Server 3.51Windows for Workgroups Ver. 3.11

3 Connecting to a Windows NT Server 3.51Windows 95 SR2Windows 95 SR2 Requirements• HP Vectra with Windows 95 SR2 loaded.• 3COM Etherlink 3C590 PCI Et

NoticeThe information contained in this document is subject to change without notice.Hewlett-Packard makes no warranty of any kind with regard to this

3 Connecting to a Windows NT Server 3.51Windows 95 SR29 When prompted, click on “OK” to continue.10 Enter “Computer Name”, “Workgroup”, and “Computer

3 Connecting to a Windows NT Server 3.51Windows NT Workstation Version 3.51Windows NT Workstation Version 3.51Requirements• HP Vectra with Microsoft

3 Connecting to a Windows NT Server 3.51Windows NT Workstation Version 3.519 Open the “Main” program group, and double-click on “Control Panel.”10 Op

3 Connecting to a Windows NT Server 3.51Windows NT Workstation Version 3.51administrator)25 At the “Domain/Workgroup Settings” dialog box, click on “

3 Connecting to a Windows NT Server 3.51Windows NT Workstation Version 3.51

3 Connecting to a Windows NT Server 3.51Windows NT Workstation 4.0Windows NT Workstation 4.0Requirements• HP Vectra with Windows NT Workstation 4.0 i

3 Connecting to a Windows NT Server 3.51Windows NT Workstation 4.08 Power on the machine and allow it to boot to Windows NT Workstation 4.0.9 Log ont

3 Connecting to a Windows NT Server 3.51Windows NT Workstation 4.024 When “Windows NT is now ready to start the network…” click on “Next.”25 Specify

3 Connecting to a Windows NT Server 3.51Windows NT Workstation 4.0

4. Connecting to a Windows NT Server 4.0Windows for Workgroups Ver. 3.114. Connecting to a Windows NT Server 4.0Windows for Workgroups Ver. 3.11Requi

1 Connecting to a Netware 3.12 ServerWindows for Workgroups1 Connecting to a Netware 3.12 ServerWindows for WorkgroupsRequirements• HP Vectra with DOS

4. Connecting to a Windows NT Server 4.0Windows for Workgroups Ver. 3.118 After windows loads, open the “NETWORK” program group, and double-click on “

4. Connecting to a Windows NT Server 4.0Windows for Workgroups Ver. 3.11“Windows Setup” dialog box.

4. Connecting to a Windows NT Server 4.0Windows for Workgroups Ver. 3.11

4 Connecting to a Windows NT Server 4.0Windows 95 SR2Windows 95 SR2 Requirements• HP Vectra with Windows 95 SR2 loaded.• 3COM Etherlink 3C590 PCI Ethe

4 Connecting to a Windows NT Server 4.0Windows 95 SR29 When prompted, click on “OK” to continue.10 Enter “Computer Name”, “Workgroup”, and “Computer D

4 Connecting to a Windows NT Server 4.0Windows NT Workstation Version 3.51Windows NT Workstation Version 3.51Requirements• HP Vectra with Microsoft Wi

4 Connecting to a Windows NT Server 4.0Windows NT Workstation Version 3.519 Open the “Main” program group, and double-click on “Control Panel.”10 Open

4 Connecting to a Windows NT Server 4.0Windows NT Workstation Version 3.51administrator)25 At the “Domain/Workgroup Settings” dialog box, click on “OK

4 Connecting to a Windows NT Server 4.0Windows NT Workstation Version 3.51

4 Connecting to a Windows NT Server 4.0Windows NT Workstation 4.0Windows NT Workstation 4.0Requirements• HP Vectra with Windows NT Workstation 4.0 ins

1 Connecting to a Netware 3.12 ServerWindows for Workgroups6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows di

4 Connecting to a Windows NT Server 4.0Windows NT Workstation 4.08 Power on the machine and allow it to boot to Windows NT Workstation 4.0.9 Log onto

4 Connecting to a Windows NT Server 4.0Windows NT Workstation 4.027 To complete the installation, select “Yes” to reboot your computer.

4 Connecting to a Windows NT Server 4.0Windows NT Workstation 4.0

Version Number 3COM 590 PCI Rev.1

1 Connecting to a Netware 3.12 ServerWindows for Workgroupsand hit enter.11 Insert the 3COM Etherlink 3C590 Ethernet card and drivers disk, set the pa

1 Connecting to a Netware 3.12 ServerWindows for Workgroups

1 Connecting to a Netware 3.12 ServerWindows 95 SR2Windows 95 SR2 Requirements• HP Vectra with Windows 95 SR2 installed.• 3COM Etherlink 3C509-B ethe

1 Connecting to a Netware 3.12 ServerWindows 95 SR2ethernet card8 When prompted, click on “OK” to continue.9 Enter “Computer Name”, “Workgroup”, and

2 Connecting to a Netware 4.11 ServerWindows for Workgroups2 Connecting to a Netware 4.11 ServerWindows for WorkgroupsRequirements• HP Vectra with D