Hp VA 7400 Manual do Utilizador

Hewlett-Packard VA 7100/7400 Microsoft Cluster Services Installation Guide for HP Netservers Version 1.0 October 12, 2001

VA 7100/7400 Cluster Installation Guide 10/12/01 7 2. Referring to the window shown below, type vfpfmt at the Ready prompt, then strike the Enter ke

VA 7100/7400 Cluster Installation Guide 10/12/01 8 3. Insert the CD containing the HP Surestore Command View SDM software in the CD-ROM drive. On t

VA 7100/7400 Cluster Installation Guide 10/12/01 9 5. On the Command View CD window shown below, click RunInst.

VA 7100/7400 Cluster Installation Guide 10/12/01 10 6. On the InstallShield Wizard for hp command view sdm window shown below, click Next.

VA 7100/7400 Cluster Installation Guide 10/12/01 11 7. On the License Agreement window shown below, click the I accept the terms in the license agree

VA 7100/7400 Cluster Installation Guide 10/12/01 12 8. On the Minimum Requirements window shown below, verify that the six settings are checked as sh

VA 7100/7400 Cluster Installation Guide 10/12/01 13 9. The Installing hp command view sdm window as shown below appears and begins the software insta

VA 7100/7400 Cluster Installation Guide 10/12/01 14 10. On the InstallShield Wizard Completed window shown below, click Finish.

VA 7100/7400 Cluster Installation Guide 10/12/01 15 11. The Starting HostAgent window shown below appears, and remains for a few minutes. 12. The Co

VA 7100/7400 Cluster Installation Guide 10/12/01 16 13. On the desktop display shown below, click the hp command view sdm icon. 14. The hp command

VA 7100/7400 Cluster Installation Guide 10/12/01 ii Notice The information contained in this document is subject to change without notice. Hewlett-Pa

VA 7100/7400 Cluster Installation Guide 10/12/01 17 15. The hp command view sdm window appears. If necessary, click the Identity tab to obtain the V

VA 7100/7400 Cluster Installation Guide 10/12/01 18 16. The display of the hp command view sdm window under the LUN Management tab appears. Use the

VA 7100/7400 Cluster Installation Guide 10/12/01 19 AutoPath Setup To set up AutoPath for Windows 2000, proceed as follows: 1. Ensure that AutoPath

VA 7100/7400 Cluster Installation Guide 10/12/01 20 4. Click on Device Settings and observe that the Device Settings window for the selected LUN is d

VA 7100/7400 Cluster Installation Guide 10/12/01 21 Create Permission File An ASCII permission file for the disk array to read must be created. Perm

VA 7100/7400 Cluster Installation Guide 10/12/01 22 Identifying World-Wide Node Names The simplest method to identify world-wide node names is to us

VA 7100/7400 Cluster Installation Guide 10/12/01 23 4 Create the Cluster Service Domain Account, Service Group, OU Group Policy Introduction This pr

VA 7100/7400 Cluster Installation Guide 10/12/01 24 Account/Group Creation Procedure To create the domain user account and the new user (global secur

VA 7100/7400 Cluster Installation Guide 10/12/01 25 6. After the account has been created and made a member of the cluster group, ensure that it is

VA 7100/7400 Cluster Installation Guide 10/12/01 26 NOTE The following step places the newly-created Cluster Group (Genuity Cluster Group) into the

VA 7100/7400 Cluster Installation Guide 10/12/01 iii Contents 1 Overview ...

VA 7100/7400 Cluster Installation Guide 10/12/01 27 NOTE The following steps create a GPO at the OU level to contain the security policy settings th

VA 7100/7400 Cluster Installation Guide 10/12/01 28 11. When the Group Policy window shown below opens, in the left-hand pane, click Windows Settings

VA 7100/7400 Cluster Installation Guide 10/12/01 29 13. Perform step 12 above to edit the policy setting for each of the following user rights: o Loa

VA 7100/7400 Cluster Installation Guide 10/12/01 30 NOTE The following two steps are to be performed locally on each cluster node. Log on to each n

VA 7100/7400 Cluster Installation Guide 10/12/01 31 5 Node 1 (Primary Node) Configuration Introduction This chapter contains the step-by-step proced

VA 7100/7400 Cluster Installation Guide 10/12/01 32 3. Open the Run window as shown below by clicking the desktop Start -> Run. In the Open text

VA 7100/7400 Cluster Installation Guide 10/12/01 33 CAUTION It is very important not to upgrade disks because the cluster can only use basic disks,

VA 7100/7400 Cluster Installation Guide 10/12/01 34 9. In the Disk Manager window of step 8, right-click on one of the Unknown disks (Disk 3, in thi

VA 7100/7400 Cluster Installation Guide 10/12/01 35 12. In the Specify Partition Size window that appears as shown below, enter the desired partition

VA 7100/7400 Cluster Installation Guide 10/12/01 36 14. In the Format Partition window that appears as shown below, select Format this partition with

VA 7100/7400 Cluster Installation Guide 10/12/01 1 1 Overview General Information This document provides procedures for setting up a Windows 2000 clu

VA 7100/7400 Cluster Installation Guide 10/12/01 37 15. In the Completing the Create Partition Wizard window that appears as shown below, review the

VA 7100/7400 Cluster Installation Guide 10/12/01 38 6 Cluster Setup Introduction This chapter provides detailed instructions for performing the clust

VA 7100/7400 Cluster Installation Guide 10/12/01 39 Cluster Setup Procedure To perform the cluster setup procedure, proceed as follows: 1. In the Add

VA 7100/7400 Cluster Installation Guide 10/12/01 40 4. In the Create or Join a Cluster window shown below, select The first node in the cluster, then

VA 7100/7400 Cluster Installation Guide 10/12/01 41 7. In the Add or Remove Managed Disks window shown below, select the disk array to be used for th

VA 7100/7400 Cluster Installation Guide 10/12/01 42 9. In the Configure Cluster Network dialog box shown below, click Next. 10. In the Network Conne

VA 7100/7400 Cluster Installation Guide 10/12/01 43 11. In the Network Connections window for the dedicated Ethernet internal connection shown below,

VA 7100/7400 Cluster Installation Guide 10/12/01 44 13. In the Cluster IP Address window shown below, enter 15.18.116.215 in the IP address field, an

VA 7100/7400 Cluster Installation Guide 10/12/01 45 16. Open the Cluster Administrator window as shown below by clicking the desktop Start -> Pro

VA 7100/7400 Cluster Installation Guide 10/12/01 46 7 Node 2 (Secondary/Passive Node) Configuration Introduction This chapter contains the step-by-s

VA 7100/7400 Cluster Installation Guide 10/12/01 2 2 Pre-Installation Requirements Introduction This chapter provides a sequence of pre-installation

VA 7100/7400 Cluster Installation Guide 10/12/01 47 4. In the Cluster Name window shown below, type CLUS2 in the cluster name field. Then, enter clu

VA 7100/7400 Cluster Installation Guide 10/12/01 48 6. In the Completing the Cluster Service Configuration Wizard window shown below, click Finish to

VA 7100/7400 Cluster Installation Guide 10/12/01 49 A Configuration Worksheet Manual Configuration Worksheet This sheet should be filled out complet

VA 7100/7400 Cluster Installation Guide 10/12/01 3 NOTE In the future, the documentation listed below will be supplied in kit form as part of the VA

VA 7100/7400 Cluster Installation Guide 10/12/01 4 Local System Configuration The remainder of this procedure assumes that both HP Netservers have be

VA 7100/7400 Cluster Installation Guide 10/12/01 5 3 Configuring the Virtual Array Introduction This chapter contains detailed instructions for setu

VA 7100/7400 Cluster Installation Guide 10/12/01 6 Virtual Array Setup and Configuration Procedure To perform the virtual array setup and configurati