Hp OmniBook 800 Notebook PC Manual do Utilizador

1-1HP OmniBook 800 Docking SystemUser’s Guide

Using the Docking SystemUnderstanding the Basics1-10 5. Slide the OmniBook into the docking system until it’s fully seated. Press firmly.The docking

Using the Docking SystemUnderstanding the Basics1-11To undock the OmniBook 1. Make sure ac power is connected to the docking system. 2. If you’re usi

Using the Docking SystemUnderstanding the Basics1-12 6. Slide forward a release latch on the docking system and remove the OmniBook. 7. If you’re us

Using the Docking SystemUnderstanding the Basics1-13To manually undock the OmniBookIf for some reason you can’t undock the OmniBook using the Undock

Using the Docking SystemUnderstanding the Basics1-14To attach a security cableYour docking system has a built-in security connector that allows you t

Using the Docking SystemUnderstanding the Basics1-15To set a docking passwordPassword security protects access to your OmniBook. If you use password

Using the Docking SystemUnderstanding the Basics1-16To understand docking status lightsThe red and green lights on the docking system indicate the cu

Using the Docking SystemMaking Connections1-17Making Connections♦ Power (ac adapter).♦ External keyboard.♦ External mouse.♦ External display.♦ Floppy

Using the Docking SystemMaking Connections1-18To connect an external keyboardYou can use the built-in and external keyboards while docked. 1. Attach t

Using the Docking SystemMaking Connections1-19To connect a serial mouse 1. If you’re using Windows 95, go to step 2. –or– If you’re using Windows for

1-2NoticeThis manual and any examples contained herein are provided “as is” and aresubject to change without notice. Hewlett-Packard Company makes no

Using the Docking SystemMaking Connections1-20To switch back to the OmniBook pop-out mouseUse this procedure to switch back to the built-in OmniBook m

Using the Docking SystemMaking Connections1-21To enable the built-in and external displayssimultaneouslyIf you enable the built-in display while runni

Using the Docking SystemMaking Connections1-22To connect a serial deviceThe docking system’s 9-pin serial port is a standard serial port, just like th

Using the Docking SystemMaking Connections1-23To connect SCSI devicesSCSI devices are disabled whenever you turn off the system or undock. 1. Make sur

Using the Docking SystemMaking Connections1-24 5. If you’re using Windows 95, the OmniBook automatically detects the newdevice and sets it up for you.

Using the Docking SystemMaking Connections1-25To install an ISA or PCI expansion boardYou can install one expansion board in the docking system, such

Using the Docking SystemMaking Connections1-26 3. Turn the docking system over. Insert a straightened paper clip or other thinobject into the security

Using the Docking SystemMaking Connections1-27 5. Lift off the top of the case gently. Do not dislodge the On/Off and Undockbuttons. 6. Important: D

Using the Docking SystemMaking Connections1-28 7. Slide the ISA or PCI board into the appropriate slot and position it carefully.Support the docking s

Using the Docking SystemMaking Connections1-29To remove a device from the Undocked configuration • When Windows 95 installs a new SCSI device or ISA o

1-3Contents1 Using the Docking System ... . 1-5Understanding the Basics ... 1-8To dock the Om

Using the Docking SystemMaking Connections1-30

Using the Docking SystemUsing a Video Card1-31Using a Video CardThe docking system supports the use of a PCI video card. You must have a BIOS(System S

Using the Docking SystemUsing a Video Card1-32To dock an OmniBook with a video cardIf you have a video card installed, then you need to reboot the Omn

1-332 Troubleshooting

1-34TroubleshootingIf you run into problems using the docking system, you can use the suggestions inthis chapter for getting back on track.HintsIf you

TroubleshootingSolving Basic Problems1-35Solving Basic ProblemsIf you have a problem using the docking system, find the symptom below thatmatches your

TroubleshootingSolving Basic Problems1-36If network connections don’t work • Make sure that the LAN cable is connected. • You normally lose connection

TroubleshootingSolving Basic Problems1-37If a network-enabled system locks up when rebooting • Make sure to remove any undocked configuration for an I

TroubleshootingSolving Basic Problems1-38If the OmniBook isn’t released after pressing the Undock button • If you’re using a password, make sure it’s

1-393 Specifications and RegulatoryInformation

1-43 Specifications and Regulatory Information ... .. 1-39Hardware Specifications ... 1-41Regulatory Infor

1-40Specifications and Regulatory InformationYour OmniBook docking system is designed to provide trouble-free operation. Thefollowing suggestions can

Specifications and Regulatory InformationHardware Specifications1-41Hardware SpecificationsInterfacesSerial: one 9-pin 115,200-baud RS-232 port (with

Specifications and Regulatory InformationRegulatory Information1-42Regulatory InformationThis section presents information that shows how the docking

Specifications and Regulatory InformationRegulatory Information1-43CanadaThis digital apparatus does not exceed the Class B limits for radio noise emi

Specifications and Regulatory InformationRegulatory Information1-44EuropeProducts sold in Europe by Hewlett-Packard and its authorized dealers meet th

1-51 Using the Docking System

1-6Using the Docking SystemCongratulations! With the purchase of your OmniBook docking system, thetransformation of your OmniBook 800 into a true desk

1-7How to Use This ManualThe procedures in this manual differ slightly depending on the operating systemyou’ve installed—Windows 95 or Windows for Wor

Using the Docking SystemUnderstanding the Basics1-8Understanding the BasicsThis section shows you how to get your docking system and OmniBook up andr

Using the Docking SystemUnderstanding the Basics1-9CAUTIONDo not use the ac adapter from another product. Using an improper adaptercould damage your