HP Compaq t5730 Thin Client Guia do Utilizador

Hardware Reference GuideHP Compaq t5730/t5735 Thin Clients

The wireless antenna allows you to send and receive wireless signals to communicate with wirelesslocal area networks (WLAN).The secure USB compartment

Installing the Antenna (Wireless Models)▲Screw the antenna in place on top of the thin client.Figure 1-5 Installing the antennaCAUTION: To prevent da

Installing the StandTo install the stand:1. Turn unit upside down.2. Locate the slots on the bottom of the unit into which the tabs on the stand fit.3

Using the KeyboardFigure 1-9 Keyboard features(1) Caps Lock key Activates/deactivates the Caps Lock feature.(2) Scroll Lock key Activates/deactivates

Windows Logo KeyUse the Windows Logo Key in combination with other keys to perform certain functions available inWindows operating systems.Windows Log

Serial Number LocationEvery thin client includes a unique serial number located as shown in the following illustration. Have thisnumber available when

2 Hardware ChangesGeneral Hardware Installation SequenceTo ensure the proper installation thin client hardware components:1. Back up any data, if nece

8. Replace the secure USB compartment cover. See Removing and Replacing the Secure USBCompartment Cover on page 12.9. Reconnect any external devices a

Removing and Replacing the Secure USB CompartmentCoverThe secure USB compartment allows you to install two USB devices in a secure location inside the

1. Place the cover on top of the unit so it is offset about 1.27 cm (1/2 inch) toward the rear of the unit,allowing the tabs on the cover to align and

© Copyright 2007 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft and Windows are

Removing and Replacing the Side Access Panel and MetalSide CoverRemoving the Side Access Panel and Metal Side CoverWARNING! Before removing the side a

2. Lift the metal side cover, front side first, off the unit (2).Figure 2-4 Removing the metal side coverReplacing the Metal Side Cover and Side Acce

3. Replace the screw that secures the access panel to the chassis (3).Figure 2-6 Replacing the side access panelInstalling Thin Client OptionsVarious

Installing the USB DeviceBefore beginning the replacement process, review General Hardware Installation Sequenceon page 10 for procedures you should f

2. To release the battery from its holder, squeeze the metal clamp that extends above one edge ofthe battery. When the battery pops up, lift it out (1

External DrivesVarious external USB drives are available as options for the t5730/t5735. For more information aboutthese drives, visit http://www.hp.c

A SpecificationsTable A-1 HP Compaq t5730/t5735 Thin ClientDimensionsWidth (front to back)Height (top to bottom)Depth46 mm254.5 mm215.18 mm1.811 in.1

Rated Line FrequencyPower Output (maximum) 50 W 50 WRated Output Current (maximum) 4.16 A 4.16 AOutput Voltage +12 V DC +12 V DCTable A-1 HP Compaq t

B Security ProvisionsSecuring the Thin ClientThe HP Compaq t5730/t5735 thin client is designed to accept a security cable lock. This cable lockprevent

C Mounting the Thin ClientHP Quick ReleaseThe HP Compaq t5730/t5735 thin client incorporates four mounting points on each side of the unit.These mount

About This BookWARNING! Text set off in this manner indicates that failure to follow directions could result in bodilyharm or loss of life.CAUTION: Te

To use the HP Quick Release with a VESA-configured thin client:1. Using four 10 mm screws included in the mounting device kit, attach one side of the

3. Slide the side of the mounting device attached to the thin client (1) over the other side of themounting device (2) on the device on which you want

Figure C-6 Thin client mounted on back of monitor stand●You can mount the thin client on a wall.Figure C-7 Thin client mounted on wall●You can mount

Non-supported Mounting OptionCAUTION: Mounting a thin client in an non-supported manner could result in failure of the HP QuickRelease and damage to t

D Thin Client OperationRoutine Thin Client CareUse the following information to properly care for your thin client:●Never operate the thin client with

Figure D-2 Horizontal orientation●You can lay the thin client under a monitor stand with at least one inch of clearance.Figure D-3 Under monitor sta

Non-supported OrientationHP does not support the following orientation for the thin client.CAUTION: Non-supported placement of thin clients could resu

E Electrostatic DischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

F Shipping InformationShipping PreparationFollow these suggestions when preparing to ship the thin client:1. Turn off the thin client and external dev

IndexAaccess panelremoving 14replacing 15altitude specifications 20antennainstalling 5location 3Bbattery, replacing 17Ccable lock slot location 3cable

iv About This Book

power LED location 2power output specifications 21power supply specifications 20preventing electrostaticdamage 31PS/2 connectors location 4Rrated outp

Table of contents1 Product FeaturesStandard Features ...

Appendix C Mounting the Thin ClientHP Quick Release ...

1 Product FeaturesStandard FeaturesThank you for purchasing an HP Compaq thin client. We hope you have years of use from our t5730 ort5735 thin client

Front Panel ComponentsFigure 1-1 Front panel components(1) Secure USB compartment (5) Power LED(2) Power button (6) Line-out (headphone) audio connec

Top ComponentsFigure 1-2 Top components, external view(1) Wireless antenna*(2) Secure USB compartment(3) Cable lock slot*Available on some models. Re