HP NetServer LH 3/LH Guia de Instalação Página 1

HP NetServer LH 3/LH 3rProcessor UpgradeInstallation GuideHP Part Number 5967-2106Printed in June 1998

Chapter 1 Processor Module Installation6Removing the HP NetServer LH 3r System BoardThe bezel and cover panels must be removed to access the system bo

Chapter 1 Processor Module Installation7Extending the HP NetServer LH 3r from the RackExtend the NetServer chassis from the rack to access the cover p

Chapter 1 Processor Module Installation8Figure 1-5. Screw and Cover LocationsRemoving Cover PanelsThe NetServer has three removable cover panels (see

Chapter 1 Processor Module Installation9Figure 1-6. HP NetServer LH 3r Covers1. Remove cover 2 by unscrewing the thumbscrew, pulling the coverforward,

Chapter 1 Processor Module Installation10Removing the HP NetServer LH 3r System BoardRemove the system board from the NetServer chassis to upgrade the

Chapter 1 Processor Module Installation11Place crosspieceoff edge ofwork surfaceFigure 1-8. Placing the System Board on the Work SurfaceProceed to the

Chapter 1 Processor Module Installation12Removing the Terminator BoardIf your system has one processor, a terminator board is installed in the upper s

Chapter 1 Processor Module Installation13Removing the Processor ModuleIf you are upgrading an existing processor module, you must first remove themodu

Chapter 1 Processor Module Installation14Processor Ejector LevelProcessor ModuleReleaseLatchProcessorMountingBracketFigure 1-11. Removing the Processo

Chapter 1 Processor Module Installation15Installing a New Processor ModuleTo install a processor module:1. Orient the new processor module as shown in

iiNoticeThe information contained in this document is subject to change without notice.Hewlett-Packard makes no warranty of any kind with regard to th

Chapter 1 Processor Module Installation16Figure 1-12. Installing a New Processor Module

Chapter 1 Processor Module Installation17Installing a New Voltage Regulator ModuleOne voltage regulator module (VRM) must be installed for each proces

Chapter 1 Processor Module Installation18Do not push hereMain VRM BoardVRM SocketReleaseLatches(shown in openposition)Figure 1-13. Installing a New VR

Chapter 1 Processor Module Installation19Setting the Processor Speed SwitchesAfter installing processors, verify that the processor speed switches are

Chapter 1 Processor Module Installation20Completing the InstallationComplete the processor module installation by installing the system board,covers,

Chapter 1 Processor Module Installation21Completing the HP NetServer LH 3r InstallationTo complete the installation:1. Insert the system board into th

Chapter 1 Processor Module Installation224. See Figure 1-15. Slide the server into the rack and attach the bezel hingeto the two (previously install

Chapter 1 Processor Module Installation235. Snap the bezel in place so it swings open to access the HP NetServerLH 3r internal mass storage cage. See

Chapter 1 Processor Module Installation24Updating the BIOSAfter upgrading the processor module(s) or adding a processor module to aNetServer, the BIOS

252 Warranty and SupportThe hardware warranty below applies to components purchased as accessories. Ifyour component was factory installed as part of

iiiContents1 Processor Module Installation...1About This Upgrade Accessory...

27A Regulatory InformationFor regulatory information pertaining to this HP accessory, please refer to theregulatory section of the user guide for the

29IndexAaccessory kit, Contents, 2anti-tip foot, rack, 7BbezelLH 3, 4LH 3r, 6, 22BIOS, updating, 24CCautionBIOS versions, 24cover and bezel installati

Index30WWarninganti-tip foot, 7power and cable disconnect, 3warranty informationhardware, 25

11 Processor Module InstallationAbout This Upgrade AccessoryThis accessory kit is provided as an upgrade to both the HP NetServer LH 3 (thefloor-stand

Chapter 1 Processor Module Installation2Accessory Kit ContentsThis accessory kit contains the following items:• Pentium II processor module• Voltage r

Chapter 1 Processor Module Installation3To install this accessory you need the following tools, plus the key for the frontlock, if the HP NetServer is

Chapter 1 Processor Module Installation4Removing the HP NetServer LH 3 CoversThe bezel and cover 3 must be removed to access the system board.Removing

Chapter 1 Processor Module Installation5Removing the Cover PanelsThe NetServer has three removable cover panels (see Figure 1-2):• Cover 1 covers the