HP NetServer LXr 8000 Especificações Página 10
- Página / 50
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 1 Introduction
5
Table 1-1. Alternative Installation Operations
Received Kit: Initial installation of
HP NetServer with the Compaq
rack-optimized kit
Awaiting Kit: Initial installation of
HP NetServer without Compaq
rack-optimized kit, followed by later
installation of kit
1. Remove bezel latch, control panel bezel,
and LCD cover (Chapter 2).
1. Prepare Compaq rack (Chapter 3).
2. Install new LCD cover and new control
panel bezel (Chapter 2).
2. Install HP NetServer into rack with
existing LCD cover and control panel
bezel, but no front bezel (Chapter 4).
3. Prepare Compaq rack (Chapter 3). 3. After the kit is received: extend
HP NetServer from rack (Chapter 2).
4. Install HP NetServer in rack (Chapter 4). 4. Remove bezel latch, control panel bezel,
and LCD cover (Chapter 2).
5. Install Compaq rack-optimized
nameplate and front bezel (Chapter 4).
5. Install new LCD cover and new control
panel bezel (Chapter 2).
6. Install Compaq rack-optimized
nameplate and front bezel (Chapter 4).
Compaq Rack Precautions
WARNING To prevent the rack from tipping over and causing equipment
damage or bodily injury, be sure that the stabilizing, anti-tip
feature is installed on this rack enclosure (see Figure 1-2).
To prevent the rack from tipping over and causing equipment
damage or bodily injury, do not extend more than one piece of
equipment at a time out of the front of the rack enclosure.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
- 1
- HP Part Number 5967-6670 2
- Printed in September 1999 2
- Audience Assumptions 3
- Contents 4
- About This Guide 6
- 1 Introduction 8
- Chapter 1 Introduction 9
- Compaq Rack Precautions 10
- Front Stabilizing 11
- "Feet" 11
- Side Stabilizing 11
- (Both Sides) 11
- • Use APC 12
- Table 1-2. Terms 13
- 2 Preparing the HP NetServer 14
- Disconnect the HP NetServer 15
- Extend the HP NetServer 16
- Figure 2-2 17
- Remove Bezel Latch 18
- Control Panel Bezel 19
- Snap Latch 19
- (2 Places) 19
- Top Cov er 20
- (HP NetServer LXr 8500 Shown) 22
- Disconnect the LCD Cables 23
- Remove the Existing LCD Cover 24
- Install the New LCD Cover 26
- Post (4 Places) 28
- Hole in Processor Tray 28
- LCD Assembly 28
- Reconnect the LCD Cables 29
- 3 Preparing the Rack 34
- Chapter 3 Preparing the Rack 35
- Install the Cage Nuts 36
- Adjust the Slides 36
- Mount the Slides 37
- 4 Installing into the Rack 38
- Lifting Handles 40
- (2 more on other side) 40
- Extended 40
- Slide Members 40
- Install the Nameplate 43
- A Warranty and Support 46
Manuais e produtos relacionados com Barebones PC/estação de trabalho HP NetServer LXr 8000
(63 páginas)
Barebones PC/estação de trabalho HP StorageWorks 20 - Modular Smart Array Especificações
(46 páginas)
(46 páginas)
Barebones PC/estação de trabalho HP T1010 - Windows-based Terminals - 48 MB RAM Manual do Utilizador
(16 páginas)
(16 páginas)
Barebones PC/estação de trabalho HP MS214 - Pavilion All-in-One - 2 GB RAM Especificações
(246 páginas)
(246 páginas)
Barebones PC/estação de trabalho HP Compaq Presario,Presario CQ2002 Informações Técnicas
(133 páginas)
(133 páginas)
DeVilbiss COMPACT P2-11 manuály
Uživatelské manuály a uživatelské příručky pro Stříkací barva DeVilbiss COMPACT P2-11.
Poskytujeme 2 manuály pdf DeVilbiss COMPACT P2-11 ke stažení zdarma podle typů dokumentů: Uživatelský manuál, Specifikace
Comentários a estes Manuais