HP ProLiant Smart Array E200 Guia do Utilizador descarregar pdf (Página 20)

Operations 20

WARNING: To reduce the risk of personal injury, be careful when pressing the server

rail-release latches and sliding the server into the rack. The sliding rails could pinch your

fingers.

5. After performing the installation or maintenance procedure, slide the server into the rack:

a. Slide the server fully into the rack.

b. Secure the server by tightening the thumbscrews.

6. Connect the peripheral cables and power cords.

Remove the access panel

WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and

the internal system components to cool before touching them.

CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating

the server in this manner results in improper airflow and improper cooling that can lead to thermal damage.

1. Power down the server if the standard cable management solution is installed ("Power down the

server" on page 18).

NOTE: If the optional cable management arm is installed, you can extend the server and perform hot-plug

installation or maintenance procedures without powering down the server.

2. Extend or remove the server from the rack ("Extend the server from the rack" on page 19).

3. Lift up on the hood latch handle and remove the access panel.

Install the access panel

1. Place the access panel on top of the server with the hood latch open. Allow the panel to extend past

the rear of the server approximately 0.8 cm (0.2 in).

2. Engage the anchoring pin with the corresponding hole in the latch.

3. Push down on the hood latch. The access panel slides to a closed position.

Remove the PCI riser board assembly

CAUTION: To prevent damage to the server or expansion boards, power down the server and remove all

AC power cords before removing or installing the PCI riser board assembly.

1. Power down the server (on page 18).

2. Extend or remove the server from the rack ("Extend the server from the rack" on page 19).

3. Remove the access panel (on page 20).

4. Remove the PCI riser board assembly:

a. Disconnect external cables connected to any existing expansion boards.

b. Loosen the four PCI riser board assembly thumbscrews.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 117 118

Comentários a estes Manuais

Sem comentários

Conceptronic C20-150 Ficha de datos (3 paginas)

Marca: Conceptronic | Categoria: HDD/SSD enclosures | Tamaño: 0.26 MB |

Tabla de contenidos

CHD2SUSB3 C20-150

Más productos y manuales para Hdd / ssd recintos Conceptronic

Modelos	Tipo de documento
C20-258	Ficha de datos Conceptronic 2,5" Harddisk Box Mini Violet USB powered, 3 paginas
C05-210	Ficha de datos Conceptronic 3,5 inch USB hard disk box for SATA hard disk, 3 paginas
C05-500	Ficha de datos Conceptronic 2,5 / 3,5 inch hard disk docking station eSATA/USB, 3 paginas
CHD3SATA	Ficha de datos Conceptronic Serial ATA External Hard disk box 3.5 “., 1 paginas
C10-393	Ficha de datos Conceptronic Grab'n'GO 2.5” Hard Disk Box eSATA/USB 2.0, 3 paginas
C05-326	Ficha de datos Conceptronic USB SATA HDD 2.5" BLACK USB powered, 3 paginas
C10-135	Ficha de datos Conceptronic 3,5 inch USB/e-SATA hard disk box, 3 paginas
C05-106	Ficha de datos Conceptronic USB 2.0 & Firewire Harddisk Box 3.5", 1 paginas
C05-324	Ficha de datos Conceptronic 3,5 inch HardDiskBox DualBay, 3 paginas
C20-253	Ficha de datos Conceptronic 2,5" Harddisk Box Mini Blue USB powered, 3 paginas
C05-209	Ficha de datos Conceptronic 2,5 inch USB hard disk box for SATA hard disk, 3 paginas
CHD3U	Ficha de datos Conceptronic USB 2.0 Hard Disk Box 3.5", 1 paginas

HP ProLiant Smart Array E200 Guia do Utilizador Página 20

Comentários a estes Manuais

Conceptronic C20-150 manuales

Conceptronic C20-150 Ficha de datos (3 paginas)

Tabla de contenidos

Más productos y manuales para Hdd / ssd recintos Conceptronic

HP ProLiant Smart Array E200 Guia do Utilizador Página 20

Comentários a estes Manuais

Manuais e produtos relacionados com Servidores HP ProLiant Smart Array E200

Conceptronic C20-150 manuales

Conceptronic C20-150 Ficha de datos (3 paginas)

Tabla de contenidos

Más productos y manuales para Hdd / ssd recintos Conceptronic