Use the options defined in template <template_name>. The template is created using the

createtemplate command. Options specified in the template are read-only or read-write. The

read-write options may be overridden with new options at the time of their creation, but read-only

options may not be overridden at creation time. Options not explicitly specified in the template

take their default values, and all of these options are either read-only or read-write (using the –nro

or –nrw options of the createtemplate command). Sizing options from the template are

ignored. This command does not change the size of the VV on which it acts.

–t <RAID_type>

Specifies the RAID type of the Logical Disk (LD): r0 for RAID-0, r1 for RAID-1, or r5 for RAID-5,

or r6 for RAID-6. If no RAID type is specified, the default is r1.

–ssz <size_number_chunklets>

Specifies the set size in the number of chunklets. The default depends on the RAID type specified:

2 for RAID-1, 4 for RAID-5, and 8 for RAID-6.

–rs <size>

Specifies the number of sets in a row. The <size> is a positive integer. If not specified, no row

limit is imposed.

–ss <size_KB>

Specifies the step size from 32 KB to 512 KB. The step size should be a power of 2 and a multiple

of 32. If no value is entered, the step size defaults to 256 KB for RAID-0 and RAID-1, and 128 KB

for RAID-5. For RAID-6, the default is a function of the set size.

–ha port|cage|mag

Specifies that the layout must support the failure of one port pair, one cage, or one drive magazine

(mag). This option has no meaning for RAID-0.

–ch first|last

Specifies the chunklet location preference, either first (attempt to use the lowest numbered

available chunklets) or last (attempt to use the highest numbered available chunklets). If no

argument is specified, the default location is first.

–p <pattern>

Specifies a pattern for candidate disks. Patterns are used to select disks that are used for creating

logical disks. If no pattern is specified, the option defaults to all Fibre Channel (FC) disks. If specified

multiple times, each instance of the specified pattern adds additional candidate disks that match

the pattern. The -devtype pattern cannot be used to mix Near Line (NL), FC, and Solid State

Drive (SSD) drives:

NOTE: An item is specified as an integer, a comma-separated list of integers, or a range of

integers specified from low to high.

–nd <item>

Specifies one or more nodes. Nodes are identified by one or more integers (<item>). Multiple

nodes are separated with a single comma (1,2,3). A range of nodes is separated with a hyphen

(0–7). The primary path of the disks must be on the specified node(s).

–st <item>

Specifies one or more PCI slots. Slots are identified by one or more integers (<item>). Multiple

slots are separated with a single comma (1,2,3). A range of slots is separated with a hyphen

(0–7). The primary path of the disks must be on the specified PCI slot(s).

–pt <item>

Specifies one or more ports. Ports are identified by one or more integers (<item>). Multiple ports

are separated with a single comma (1,2,3). A range of ports is separated with a hyphen (0–5).

The primary path of the disks must be on the specified port number(s).

tunealdvv 643

1 2 ... 638 639 640 641 642 643 644 645 646 647 648 ... 675 676

Comentários a estes Manuais

Sem comentários

Barco ScreenPRO-II podręczniki

Instrukcje obsługi i podręczniki użytkownika dla Telewizory i monitory Barco ScreenPRO-II.
Dostarczamy 2 pdf podręczników Barco ScreenPRO-II do pobrania za darmo według typów dokumentów: Instrukcja Obsługi, Instrukcja Użytkownika

Barco ScreenPRO-II Instrukcja Obsługi (206 strony)

Marka: Barco | Kategoria: TVs & monitors | Rozmiar: 1.98 MB |

Spis treści

• Manual # 26-0407000-00

• Revision B

=√=rëÉêÛë=dìáÇÉ

`çãé~åó=^ÇÇêÉëë

^sboqfppbjbkq>

`Ü~åÖÉ=eáëíçêó

Table of Contents

NK==fåíêçÇìÅíáçå

`çåîÉåíáçåë=

Wilderness

Background

OK==e~êÇï~êÉ=lêáÉåí~íáçå

2. Hardware Orientation

^å~äçÖ=fåéìí=cäÉñáÄáäáíó

Front Panel Sections

WIPE CUT MIX

Transitions

`~ÄäÉ=~åÇ=^Ç~éíÉê=fåÑçêã~íáçå

3. Hardware Installation

BORDER} to …

ScreenPRO II

INPUT MENU

Input Type

INPUT ACQUISITION SRC_3

Source acquired

File Name [ IFILE_003 ]

INPUT CONFIGURATION SRC_3

File Number [ 3 ]

NWN=páòáåÖ=jÉåì

`çäçê=_~ä~åÅÉ=jÉåì

^ëéÉÅí=o~íáç=jÉåì

OUTPUT MENU

TEST PATTERN

Output Monitor All

Raster Box On

SYSTEM MENU

NVRAM Battery [ OK ]

DIAGNOSTICS SETUP

Reset Rotary Encoders Yes

Encoder Menu

Figure 4-21. Reset Menu

SOFTWARE VERSION

ScreenPRO II 1.00

SERIAL 1 PORT SETUP

Baud Rate 115200

8Data Bits

NONEParity

1Stop Bits

System Menu

EFFECTS MENU

Transition Rate 1.0

Transition Wipe Wipe Down

Transition Edge 16

Key Frame Effect [ LINEAR ]

Status Menu

DISPLAY SETTINGS

Brightness 85

Contrast 97

Backlight Menu

ADJUSTMENT

_çêÇÉê=jÉåì

`êçé=jÉåì

Key Menu

Green 204

Blue 260

TRACK RGB

-10 is 10 pixels below its

_~ÅâÖêçìåÇ=fåéìí=pÉíìé=jÉåì

_~ÅâÖêçìåÇ=j~ííÉ=jÉåì

Save Now?

101

DSK ADJUSTMENT

102

Important

104

{SELECT

105

4. Menu Orientation

110

RK==pó ëíÉã=pÉíìé

111

5. System Setup

112

`çãéêÉÜÉåëáîÉ=fåéìí=pÉíìé

116

SK==léÉê~íáçåë

127

ProgramPreview

129

^=tçêÇ=^Äçìí=ilp

131

_~ÅâÖêçìåÇ=qê~åëáíáçåë

133

Toggle On

135

6. Operations

137

`äÉ~êáåÖ=i~óÉêë=Ñêçã=mêçÖê~ã

140

`Ü~åÖáåÖ=íÜÉ=i~óÉê=jçÇÉ

141

• Pend on Preview Method

145

• Pend on Program Method

145

`~éíìêáåÖ=píáää=cê~ãÉë

149

^K==péÉÅáÑáÅ~íáçåë

153

^å~äçÖ=NRJéáå=a=`çååÉÅíçê

158

_K==` çåí~Åí=fåÑçêã~íáçå

165

`çåí~Åí=fåÑçêã~íáçå

166

`K==réÖê~ÇáåÖ=pçÑíï~êÉ

167

{ADD NEW}

191

INPUT SOURCE PATCH

194

Source Number 1

194

MATRIXPRO1Connection Type

194

1Router Input

194

Feature ScreenPRO-II

196

Encore Video

196

Processor

196

Barco ScreenPRO-II Instrukcja Użytkownika (6 strony)

Marka: Barco | Kategoria: TVs & monitors | Rozmiar: 1.40 MB |

Spis treści

ScreenPRO-II HD EOC

Features

Multi-screen Flexibility

ScreenPRO-II Front Panel

ScreenPRO-II Rear Panel

Enhanced Output Card

ScreenPRO-II Speciﬁcations

Więcej produktów i instrukcji dla Telewizory i monitory Barco

Modele	Rodzaj dokumentu
RHDM-2301	Instrukcja Użytkownika RHDM Series High-Definition Reference monitors, 8 strony
mDR+50-DL	Instrukcja Instalacji Barco mDR+50-DL Installation manual, 128 strony
MDRC-1119	Instrukcja Użytkownika Barco MDRC-1119 User manual [en] [ro] , 68 strony
System manual E1	Instrukcja Użytkownika Barco System manual E1 User manual, 62 strony
R9040341	Instrukcja Instalacji Barco R9040341 Installation manual, 71 strony
E-2320 C (SE)	Informacje Techniczne Barco E-2320 C (SE) Technical information, 104 strony
IMAGETILE	Instrukcja Użytkownika Universal Medical Imager, 10 strony
MFCD 1219 (TS)	Instrukcja Użytkownika Barco MFCD 1219 (TS) User manual, 36 strony
cDG67-DL	Instrukcja Użytkownika 7II-2009 TCO BARCOFichier PDF - e, 44 strony
iUtilities	Instrukcja Użytkownika SMD_bro_cms_series_l, 12 strony
iUtilities	Instrukcja Użytkownika Barco iUtilities User manual, 31 strony
MDRC-1119 HB	Instrukcja Użytkownika Lieske Elektronik Preisliste - Lieske [de] [en] [fr] , 43 strony
MDRC-2122 BL	Instrukcja Użytkownika :Technische Daten, 4 strony
HDM 5049 PLUS	Instrukcja Użytkownika La HD numérique et le 24p [en] [es] [fr] [it] , 7 strony
IMAGETILE	Instrukcja Użytkownika W W W . B A R C O . C O M [en] , 152 strony
RHDM-2301	Instrukcja Użytkownika Barco RHDM 2301 reference monitor, 8 strony

HP 3PAR Guia do Utilizador Página 643

Comentários a estes Manuais

Manuais e produtos relacionados com Software HP 3PAR

Barco ScreenPRO-II podręczniki

Barco ScreenPRO-II Instrukcja Obsługi (206 strony)

Spis treści

Barco ScreenPRO-II Instrukcja Użytkownika (6 strony)

Spis treści

Więcej produktów i instrukcji dla Telewizory i monitory Barco