Hp XP RAID Manager Software Manual do Utilizador Página 17
- Página / 205
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
3 Interoperability of Performance Monitor and other products
This chapter describes the interoperability of Performance Monitor and other products.
Cautions and restrictions for monitoring
• Storage system maintenance
If the storage system is undergoing the following maintenance operations during monitoring,
the monitoring data might contain extremely large values.
◦ Adding, replacing, or removing cache memory.
◦ Adding, replacing, or removing data drives.
◦ Changing the storage system configuration.
◦ Replacing the microprogram.
◦ Formatting or quick formatting logical devices
◦ Adding on, replacing, or removing MP blades
• Storage system power-off
If the storage system is powered off during monitoring, monitoring stops while the storage
system is powered off. When the storage system is powered up again, monitoring continues.
However, Performance Monitor cannot display information about the period while the storage
system is powered off. Therefore, the monitoring data immediately after powering on again
might contain extremely large values.
• Microprogram replacement
After the microprogram is replaced, monitoring data is not stored until the service engineer
releases the SVP from Modify mode. While the SVP is in Modify mode, inaccurate data is
displayed.
• Changing the SVP time setting
If the SVP time setting is changed while the monitoring switch is enabled, the following
monitoring errors can occur:
◦ Invalid monitoring data appears.
◦ No monitoring data is collected.
To change the SVP time setting, first disable the monitoring switch, change the SVP time setting,
and then re-enable the monitoring switch. After that, obtain the monitoring data. For details
about the monitoring switch, see “Starting monitoring” (page 28).
• WWN monitoring
You must configure some settings before the traffic between host bus adapters and storage
system ports can be monitored. For details, see “Adding new WWNs to monitor” (page 23),
“Adding WWNs to ports” (page 23), and “Connecting WWNs to ports” (page 24).
Cautions and restrictions for monitoring 17
- Mainframe Systems User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 1 Performance overview 8
- Cache Residency overview 9
- 10 Performance overview 10
- Placing data in cache 13
- Prestaging specific data 13
- Priority mode 14
- Bind mode 14
- Using Performance Control 18
- Using Performance Control 19 19
- WWN monitoring data 20
- Microprogram replacement 20
- 4 Monitoring WWNs 23
- Editing the WWN nickname 24
- Connecting WWNs to ports 24
- 5 Monitoring CUs 26
- 6 Monitoring operation 28
- Stopping monitoring 29 29
- Viewing statistics 30
- 8 Working with graphs 32
- Usage rates of MPs 34
- Usage rate of cache memory 35
- Write pending statistics 35
- Access paths usage statistics 36
- Throughput of storage system 37
- Size of data transferred 38
- Response times 39
- Cache hit rates 40
- Storing period 41
- Back-end performance 42
- Hard disk drive access rates 43
- 9 Changing display of graphs 45
- Deleting graph panel 46
- Port tab operations 53
- Analyzing traffic statistics 54
- Port tab operations 55 55
- Setting a threshold 56
- WWN tab operations 57
- WWN tab operations 61 61
- WWN tab operations 63 63
- Grouping host bus adapters 65
- Renaming an PFC group 67
- Deleting an PFC group 68
- 11 Estimating cache size 69
- 70 Estimating cache size 70
- 72 Estimating cache size 72
- Cache Residency cache areas 73
- 12 Managing resident cache 75
- 76 Managing resident cache 76
- Launching Cache Residency 77
- 78 Managing resident cache 78
- 80 Managing resident cache 80
- 13 Troubleshooting 82
- Contacting HP 83
- Related information 83
- Typographic conventions 84
- Typographic conventions 85 85
- A Export Tool 86
- Installing the Export Tool 87 87
- Using the Export Tool 88
- Using the Export Tool 89 89
- 90 Export Tool 90
- Preparing a batch file 91
- Running the Export Tool 92
- Processing time 93
- Termination code 93
- Log files 94
- Error handling 94
- Export Tool command reference 95
- Subcommand list 96
- outoption compressapply 97
- Operands 102
- Examples 108
- Short-range 109
- Description 111
- ◦ Default: 20 minutes 116
- ◦ Minimum: 1 minute 116
- Exported files 117
- Port statistics 124
- Volumes (LU) statistics 125
- MP blades 126
- Monitored CUs tab 138
- Monitored WWNs tab 138
- Edit Monitoring Switch wizard 139
- Monitor Performance window 140
- Data Range 141
- Time Range 141
- Performance Objects 141
- Selected Objects table 142
- Object field is blank 145
- Available Objects table 147
- Edit CU Monitor Mode wizard 148
- Unmonitored CUs table 149
- Confirm window 150
- View CU Matrix window 152
- Available Parity Groups table 154
- Parity Group Properties table 154
- Edit WWN wizard 155
- Edit WWN Monitor Mode wizard 156
- Unmonitored WWNs table 157
- Delete Unused WWNs window 160
- Add New Monitored WWNs wizard 160
- WWN Name 161
- Available Ports table 161
- Selected WWNs table 161
- Add to Ports wizard 163
- Monitor window 165
- Graph panel 166
- MP Properties window 167
- Edit Time Range window 168
- Setting fields 169
- Monitor Data 170
- Performance Object Selection 170
- Add Graph window 177
- Wizard buttons 185
- Navigation buttons 185
- Performance Control window 187
- Cache Residency window 195
- LDEV Information table 196
- Cache Information 197
- Operations box 198
- Multi Set dialog box 199
- Multi Release dialog box 200
- Multi-Release LDEV table 201
- Glossary 202
- 204 Index 204
Manuais e produtos relacionados com Armazenamento Hp XP RAID Manager Software
(55 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.140 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais