Hp ProLiant DL360 G6 Server Manual do Utilizador Página 44
- Página / 127
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Hardware options installation 44
• Observe the general DIMM slot population guidelines (on page 42).
• Always install DIMMs in channels 1 and 2 for each installed processor.
• Do not install DIMMs in channel 3 for any processor.
• DIMM configuration on channel 1 and channel 2 of a processor must be identical.
• In multi-processor configurations, each processor must have a valid Lockstep Memory configuration.
• In multi-processor configurations, each processor may have a different valid Lockstep Memory
configuration.
Single-processor Lockstep population order
For Lockstep memory mode configurations with a single processor, populate the DIMM slots in the following
order:
• RDIMM
o First: A and B
o Next: D and E
o Last: G and H
o Do not populate slots C, F, or I.
• UDIMM
o First: A and B
o Last: D and E
o Do not populate slots C, F, G, H, or I.
After installing the DIMMs, use RBSU to configure the system for Lockstep memory support ("Configuring
lockstep memory" on page 76).
Multi-processor Lockstep population order
For Lockstep memory mode configurations with multiple processors, populate the DIMM slots for each
processor in the following order:
• RDIMM
o First: A and B
o Next: D and E
o Last: G and H
o Do not populate slots C, F, or I.
• UDIMM
o First: A and B
o Last: D and E
o Do not populate slots C, F, G, H, or I.
After installing the DIMMs, use RBSU to configure the system for Lockstep memory support ("Configuring
lockstep memory" on page 76).
Installing a DIMM
- HP ProLiant DL360 G6 Server 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 10
- System board components 11
- DIMM slots 12
- System maintenance switch 12
- NMI jumper 13
- SAS and SATA device numbers 15
- SAS and SATA hard drive LEDs 16
- Fan modules 17
- T-10/T-15 Torx screwdriver 18
- Operations 19
- Remove the access panel 21
- Install the access panel 21
- Remove the BBWC battery pack 21
- Remove the air baffle 22
- Install the air baffle 22
- Operations 25 25
- Rack planning resources 26
- Optimum environment 26
- Temperature requirements 27
- Rack warnings 28
- Installing hardware options 29
- Setup 31 31
- Registering the server 32
- Introduction 33
- 8. Install the fan module 34
- Memory options 38
- DIMM identification 40
- Memory configurations 40
- Installing a DIMM 44
- Removing hard drive blanks 46
- Installing a SAS hard drive 47
- Hard drive blackplane option 51
- Remove all fan modules 53
- Controller options 55
- Installing the cache module 56
- Expansion board options 58
- Cabling 69
- BBWC battery pack cabling 70
- Cabling 71 71
- PCI power cabling 72
- Configuration tools 73
- Using RBSU 74
- Auto-configuration process 74
- Boot options 75
- BIOS Serial Console 75
- Configuring AMP modes 75
- Array Configuration Utility 76
- Management tools 78
- Erase Utility 79
- Redundant ROM support 79
- USB support 79
- Diagnostic tools 80
- Integrated Management Log 81
- Keeping the system current 82
- Care Pack 83
- Troubleshooting 84
- Symbols on equipment 85
- Warnings and cautions 85
- Symptom information 86
- Loose connections 88
- Troubleshooting flowcharts 89
- Service notifications 89
- Server health LEDs 89
- General diagnosis flowchart 90
- Symptoms: 92
- Troubleshooting 94 94
- POST problems flowchart 95
- OS boot problems flowchart 97
- Troubleshooting 98 98
- • Redundancy failure 99
- (http://www.hp.com/support) 100
- Troubleshooting 101 101
- System battery 102
- FCC rating label 103
- Class A equipment 103
- Class B equipment 103
- Modifications 104
- • EMC Directive 2004/108/EC 105
- Japanese notice 106
- BSMI notice 106
- Korean notice 106
- Chinese notice 107
- Laser compliance 107
- Battery replacement notice 107
- Electrostatic discharge 109
- Specifications 110
- Technical support 113
- Technical support 114 114
- Customer Self Repair 115
- Technical support 116 116
- Reparo feito pelo cliente 117
- Technical support 118 118
- Technical support 119 119
- Technical support 120 120
- Acronyms and abbreviations 121
- Index 124 124
- Index 125 125
- Index 126 126
- Index 127 127
Manuais e produtos relacionados com Hardware de computador Hp ProLiant DL360 G6 Server
(107 páginas)
(187 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais