Hp ProLiant DL320e Gen8 Server Manual do Utilizador

HP ProLiant DL320e Gen8 Server User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage

Component identification 10 Item Description 13 Fan connector 2 14 Discovery service connector 15 Fan connector 1 16 24-pin power supply connector

Component identification 11 Slot number Type Length Height Connector link width Negotiable link width 1 PCIe2 Half Half x8 x4 2 PCIe3 Hal

Component identification 12 System board LED definitions Item Description Status 1 Initialization failure Yellow = System initialization failur

Component identification 13 • Eight-bay SFF drive model Hot-plug drive LED definitions Item LED Status Definition 1 Locate Solid blue

Component identification 14 FBWC module LED definitions The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicat

Component identification 15 Fan locations

Operations 16 Operations Power up the server 1. Connect each power cord to the server. 2. Connect each power cord to the power source. 3. Press t

Operations 17 IMPORTANT: The requirement of extending or removing the server from the rack when performing installation and maintenance procedures

Operations 18 IMPORTANT: The requirement of extending or removing the server from the rack when performing installation and maintenance procedures

Operations 19 a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Do one of the following: o E

© Copyright 2012, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only war

Operations 20 5. Remove the air baffle. Install the air baffle 1. Place the air baffle on top of the server. 2. Install the access panel (on pa

Operations 21 1. Power down the server (on page 16). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each

Operations 22 2. Tighten the PCI riser cage thumbscrews. 3. Install the access panel (on page 19). 4. Do one of the following: o Slide the serve

Setup 23 Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and

Setup 24 Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when decid

Setup 25 Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of

Setup 26 WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational healt

Setup 27 WARNING: When installing a server in a telco rack, be sure that the rack frame is adequately secured at the top and bottom to the buildin

Setup 28 WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational healt

Setup 29 WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding

Contents 3 Contents Component identification ...

Setup 30 f. To finish the installation, follow the onscreen prompts. An Internet connection is required to update the firmware and systems software.

Hardware options installation 31 Hardware options installation Introduction If more than one option is being installed, read the installation instru

Hardware options installation 32 Drive installation guidelines When adding drives to the server, observe the following general guidelines: • The sy

Hardware options installation 33 5. Install the drive in the carrier. 6. Install the drive. 7. Connect each power cord to the server. 8. Connec

Hardware options installation 34 2. Prepare the drive. 3. Install the drive. 4. Determine the status of the drive from the drive LED definitions

Hardware options installation 35 6. Connect the Mini-SAS cable to the storage controller. 7. Install the storage controller ("Installing a st

Hardware options installation 36 o Low-profile controller connection 9. Secure the excess length of the Mini-SAS cable in the cable clip. 10. Co

Hardware options installation 37 16. Power up the server (on page 16). Controller options The server ships with an embedded Smart Array B120i contr

Hardware options installation 38 1. Power down the server (on page 16). 2. Remove all power: a. Disconnect each power cord from the power source.

Hardware options installation 39 o Remove the server from the rack (on page 17). 4. Remove the access panel (on page 18). 5. Remove the PCI riser

Contents 4 Introduction ...

Hardware options installation 40 b. Press the opposite end of the capacitor pack in the holder. 11. Install the access panel (on page 19). 12. Do

Hardware options installation 41 4. Remove the optical drive blank. Retain the blank for future use. 5. Remove the access panel (on page 18). 6.

Hardware options installation 42 o Four-bay LFF drive model o Eight-bay SFF drive model 8. If you are installing the optical drive in an SFF dri

Hardware options installation 43 — Four-bay LFF drive model — Eight-bay SFF drive model 10. Install the access panel (on page 19). 11. Do one

Hardware options installation 44 IMPORTANT: This server does not support mixing LRDIMMs, RDIMMs, or UDIMMs. Attempting to mix any combination of t

Hardware options installation 45 Item Description Definition 3 Data width x4 = 4-bit x8 = 8-bit 4 Voltage rating L = Low voltage (1.35V) U = Ult

Hardware options installation 46 o Memory channel 1 consists of the two DIMMs that are closest to the processor. o Memory channel 2 consists of the

Hardware options installation 47 7. Install the DIMM. 8. Install the air baffle (on page 20). 9. Install the access panel (on page 19). 10. Do o

Hardware options installation 48 6. Identify the expansion slot compatible with the new option, and then remove the cover opposite that slot. 7. I

Hardware options installation 49 o Extend the server from the rack (on page 16). o Remove the server from the rack (on page 17). 4. Remove the acc

Contents 5 Option ROM Configuration for Arrays ... 68 ROMP

Hardware options installation 50 Enabling the dedicated iLO management port The onboard NIC 1/shared iLO connector is set as the default system iLO

Hardware options installation 51 • When using BitLocker, always retain the recovery key/password. The recovery key/password is required to enter Re

Hardware options installation 52 6. Install the TPM security rivet by pressing the rivet firmly into the system board. 7. Install the access panel

Hardware options installation 53 6. Press the Esc key to exit the current menu, or press the F10 key to exit RBSU. 7. Reboot the server. 8. Enable

Cabling 54 Cabling Cabling overview This section provides guidelines that help you make informed decisions about cabling the server and hardware opt

Cabling 55 • Mini-SAS cable connected to a storage controller in the full-height expansion slot Item Description 1 Power cable 2 Capacitor pack c

Cabling 56 Four-bay LFF hot-plug drive cage cabling • Mini-SAS cable connected to the system board Item Description 1 Power cable 2 560-mm Mini

Cabling 57 • Mini-SAS cable connected to a storage controller in the low-profile expansion slot Item Description 1 Power cable 2 Capacitor pack c

Cabling 58 Item Description 3 Power cable 4 Capacitor pack cable Optical drive cabling • LFF drive cage model Item Description 1 Optical driv

Cabling 59 Item Description 1 Optical drive power cable 2 Optical drive SATA cable Power supply cabling Nonredundant power supply cabling Item

Component identification 6 Component identification Front panel components • Four-bay LFF drive model Item Description 1 Optical drive 2 Seri

Cabling 60 Redundant power supply cabling Item Description 1 24-pin power supply cable 2 26-pin RPS cable 3 4-pin power supply cable CAUTION: T

Software and configuration utilities 61 Software and configuration utilities Server mode The software and configuration utilities presented in this

Software and configuration utilities 62 iLO enables and manages the Active Health System (on page 62) and also features Agentless Management. All ke

Software and configuration utilities 63 The data that is collected is managed according to the HP Data Privacy policy. For more information see the

Software and configuration utilities 64 HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offli

Software and configuration utilities 65 HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support softwar

Software and configuration utilities 66 • Dependency checking, which ensures appropriate installation order and dependency checking between compone

Software and configuration utilities 67 IMPORTANT: RBSU automatically saves settings when you press the Enter key. The utility does not prompt you

Software and configuration utilities 68 Re-entering the server serial number and product ID After you replace the system board, you must re-enter th

Software and configuration utilities 69 The utility also provides support for the following functions: • Reconfiguring one or more logical drives •

Component identification 7 Front panel LEDs and buttons Item Description Status 1 UID button/LED Solid blue = Activated Flashing blue (1 Hz/cyc

Software and configuration utilities 70 • Diagnostics • DOS • Operating environments which do not provide native USB support Redundant ROM sup

Software and configuration utilities 71 Version control The VCRM and VCA are web-enabled Insight Management Agents tools that HP SIM uses to schedul

Troubleshooting 72 Troubleshooting Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedur

System battery replacement 73 System battery replacement If the server no longer automatically displays the correct date and time, then replace the

System battery replacement 74 IMPORTANT: Replacing the system board battery resets the system ROM to its default configuration. After replacing th

Regulatory information 75 Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety

Regulatory information 76 Valid date formats include the following: • YWW, where Y indicates the year counting from within each new decade, with 20

Electrostatic discharge 77 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Specifications 78 Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Nonop

Specifications 79 Rated input current 6 A Rated input power 430 W at 115 V 430 W at 230 V Power supply output — Efficiency Not less than 82% at 100%

Component identification 8 Rear panel components Item Description 1 Slot 2 PCIe x16 (16, 8, 4, 1)* 2 Slot 1 PCIe x8 (4, 1)* 3 Power supply 1 4 Po

Specifications 80 Rated steady-state output power 460 W at 100 V to 120 V AC output 460 W at 200 V to 240 V AC output Maximum peak power 460 W at 10

Support and other resources 81 Support and other resources Before you contact HP Be sure to have the following information available before you call

Support and other resources 82 providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship

Support and other resources 83 Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'in

Support and other resources 84 HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,

Support and other resources 85 sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes

Support and other resources 86 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pel

Support and other resources 87

Support and other resources 88

Acronyms and abbreviations 89 Acronyms and abbreviations ABEND abnormal end ACU Array Configuration Utility AMP Advanced Memory Protection ASR Au

Component identification 9 Item Description Status 2 NIC status LED Green = Activity exists Flashing green = Activity exists Off = No activity ex

Acronyms and abbreviations 90 FCC Federal Communications Commission HP CS HP Common Slot (power supply) HP SIM HP Systems Insight Manager HP SSA

Acronyms and abbreviations 91 PCIe Peripheral Component Interconnect Express PDU power distribution unit POST Power-On Self Test PXE preboot exec

Acronyms and abbreviations 92 SPP HP Service Pack for ProLiant SSA HP Smart Storage Administrator TMRA recommended ambient operating temperature

Index 93 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any err

Index 94 A access panel 19 Active Health System 61, 62 ACU (Array Configuration Utility) 61, 68 air baffle 19, 20 airflow requirements 23,

Index 95 front panel LEDs 7 G grounding methods 77 grounding requirements 25 H hard drives, determining status of 13 hardware options 27,

Index 96 recommended ambient operating temperature (TMRA) 24 recovery key 52 redundant ROM 70 registering the server 30 regulatory complianc