Hp ProLiant SL2500 Scalable System Manual do Utilizador Página 50
- Página / 117
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Power capping 50
In the following figure, the HP APM port 2 is connected to the HP APM Distribution Module port 4. The
distribution module port is connected to the SL enclosure and server node 8.
Item Description
1
HP APM
2
HP APM Distribution Module
3
SL series enclosure
4
Bay 4 of a 4U chassis SL6500 Scalable System enclosure with eight 1U half-width
nodes
Displaying the rack power status
Enter SHOW POWER, and then optionally the specific HP APM port, or both the HP APM and the HP APM
Distribution Module ports.
For example:
SHOW POWER (to show all power)
SHOW POWER 2 (to show the power for the HP APM port number)
SHOW POWER 2 4 (to show the power for the HP APM port number and the HP APM Distribution Module port
number
This command also displays:
• Fan power per chassis in DC watts
• Chassis total in DC watts
• Chassis total in AC watts
• Chassis cap in AC watts (if one is set)
• The total of the averages is shown as well as the "average of averages" that was already there
• The average max power is shown as well as the total of the max column
- HP Advanced Power Manager 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Contents 7 7
- Introduction 8
- HP APM kit contents 9
- HP APM front view 10
- HP APM rear view 11
- HP APM connections 11
- Item Component Connects To 12
- Required connections 13
- Identifying the RDM1 ports 13
- • HP Moonshot System 14
- Using RJ-45 connections 16
- Rack chassis numbering 17
- Automatic discovery 18
- Introduction 19 19
- Preparing for installation 20
- Configuring the HP APM 20
- Serial port configuration 22
- Network configuration 22
- Security configuration 23
- Protocol configuration 23
- Command Line Interface 24
- Saving configurations 25
- Topology and inventory 25
- Command Line Interface 26 26
- Command Line Interface 27 27
- Showing the servers 28
- Showing topology 28
- Showing assetinfo 29
- Showing the MAC address 30
- Command Line Interface 31 31
- Logging 32
- Logging 33 33
- Logging 34 34
- External logging 35
- HP APM fault messages 35
- XML-related fault messages 37
- Working with RADIUS servers 37
- Showing a RADIUS server 38
- Power capping 39
- Power capping licensing 40
- Rack level power capping 40
- Power baseline 41
- Power capping 42 42
- Setting power capping 43
- Power capping 44 44
- Power capping 45 45
- Power capping 46 46
- Power capping with zones 48
- Power commands 49
- Setting power 51
- Power capping 52 52
- Power capping 53 53
- General commands 54
- Working with accounts 55
- Working with zones 56
- General commands 57 57
- Using password recovery 58
- Showing configurations 59
- Using the help 59
- Setting the name 59
- Setting the time 60
- Setting the session timeout 60
- Setting the UID LED 60
- Showing information 60
- Showing the name 61
- Showing the time 61
- Showing the version 61
- General commands 62 62
- Connecting and setting ports 63
- Using SNMP 64
- Setting the SNMP contact 65
- Setting the SNMP location 65
- Using SNMP 66 66
- Using XML 67
- Response definitions 68
- Enabling XML 69
- Showing and resetting keys 69
- Logging in through XML 69
- Modifying the user account 69
- Modifying compute node power 70
- Resetting HP APM 71
- Using XML 72 72
- Firmware 73
- Troubleshooting 74
- CLI commands 75
- CLI commands 76 76
- Disable password 77
- Enable password 77
- Set password account 77
- • Description: 78
- • Command: 78
- CLI commands 79 79
- Reboot CM 80
- Reset factory 80
- Save config 80
- Set gateway 81
- Set name 81
- Set power 81
- Set serial 82
- Set syslog 82
- Set time 82
- Set timeout 82
- Set power baseline 83
- Set power cap 83
- Set asset info 83
- CLI commands 84 84
- Show name 85
- Show power 85
- Show rack 85
- Show servers 86
- Show topology 86
- Show asset info 86
- Show MAC address 87
- Show time 87
- Show power baseline 87
- Show version 87
- Upgrade image 87
- Add zone 88
- Save zones 89
- Show zones 89
- Remove zone 89
- Enable pollpower 89
- Disable pollpower 89
- Enable SNMP 90
- Disable SNMP 90
- Show SNMP 90
- Set SNMP RO 90
- Set SNMP RW 90
- Set SNMP contact 91
- Set SNMP location 91
- Set SNMP trapdest 91
- Enable XML 92
- Enable XML secure 92
- Disable XML 92
- Show keys 92
- Reset keys 92
- CLI commands 93 93
- Set RADIUS pollsec 94
- Enable NTP 94
- Set NTP server 94
- Set NTP poll 94
- Show NTP server 94
- Show NTP poll 95
- Disable NTP 95
- Connect port 95
- Set port 95
- XML commands 96
- Get rack topology 97
- Get rack information 97
- Modify compute node power 97
- Get compute node 98
- Get all compute node power 99
- Reset HP APM 99
- Supported MIB objects 100
- PDU identity table 109
- PDU input table 109
- Regulatory information 110
- Warranty information 111
- Support and other resources 112
- Acronyms and abbreviations 113
- Documentation feedback 114
- Index 115 115
- Index 116 116
- Index 117 117
Manuais e produtos relacionados com Hardware de computador Hp ProLiant SL2500 Scalable System
(172 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais