C-1

Safety and Regulatory

Statements

Safety and Regulatory Statements

This chapter covers the following topics:

■ mounting precautions

■ power precautions

■ safety statements

■ regulatory statements

■ Declaration of Conformity

Mounting Precautions

When you put a hub into a rack, follow these mounting precautions:

■ The rack or cabinet should be adequately secured to prevent it from

becoming unstable and/or falling over. The hub should be mounted in a

position toward the bottom of the rack for stability and to make it easier

to stack the other hubs on top.

■ Before mounting a hub, plan its location and orientation relative to other

devices and equipment. Also consider the cabling that will be attached to

the hub and the ports that will be used. Verify that there is room for the

grouped cables to trail out from the side of the hub. Allow at least 2.54 cm

(1 inch) in the front of the hub. In the back of the hub, allow at least 3.8

cm (1 1/2 inches) of space for the power cord.

■ Ensure that the HP ProCurve 10Base-T Hub does not overload the power

circuits, wiring, and over-current protection. To determine the possibility

of overloading the supply circuits, add together the amperage ratings from

the nameplates of all your hubs (and other equipment) installed on the

same circuits and compare the total with the rating limits for the supply

circuits.

■ Make sure that the power source circuits are properly grounded, then use

the supplied power cord to connect the HP ProCurve 10Base-T Hubs to

the circuit. See the Safety Statements in this chapter.

■ Do not block airflow around the sides and the back of the unit.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 53 54

Comentários a estes Manuais

Sem comentários

DeVilbiss COMPACT P2-11 manuály

Uživatelské manuály a uživatelské příručky pro Stříkací barva DeVilbiss COMPACT P2-11.
Poskytujeme 2 manuály pdf DeVilbiss COMPACT P2-11 ke stažení zdarma podle typů dokumentů: Uživatelský manuál, Specifikace

Modely	Typ Dokumentu
SB-2-001-F	Uživatelský manuál SB-2-259-B JGA-504 CONVENTIONAL SPRAY GUN [en] , 8 stránky
SB-2-001-F	Uživatelský manuál SB-2-362 - Coast Industrial Systems, Inc., 6 stránky
HVLP Gravity Feed Spraygun	Uživatelský manuál BINKS SV100 HVLP GRAVITY FEED SPRAY GUN, 8 stránky
SB-E-2-534	Uživatelský manuál DEVILBISS COMPACT – Gravity Feed Spraygun, 12 stránky
FAC752-3	Provozní pokyny DeVilbiss FAC752-3 Operating instructions, 12 stránky
SB-2-546	Uživatelský manuál parts breakdown, 1 stránky
SB-2-546	Uživatelský manuál SB-2-199-F, 8 stránky
SB-E-2-534	Uživatelský manuál CONV-GRAV ENG-FR-GER-534 iss2.pub, 32 stránky
SB-2-001-F	Uživatelský manuál SB-2-246-G JGHV-531 HIGH VOLUME LOW PRESSURE SPRAY, 6 stránky
SB-2-546	Uživatelský manuál For Waterborne Materials, 34 stránky

HP 10-Base-T Manual de Instalação Página 39

Comentários a estes Manuais

DeVilbiss COMPACT P2-11 manuály

Devilbiss COMPACT P2-11 Uživatelský manuál (12 strany)

Tabulka s obsahem

Devilbiss COMPACT P2-11 Specifikace (16 strany)

Tabulka s obsahem

Další produkty a příručky pro Stříkací barva DeVilbiss

HP 10-Base-T Manual de Instalação Página 39

Comentários a estes Manuais

Manuais e produtos relacionados com Redes HP 10-Base-T

DeVilbiss COMPACT P2-11 manuály

Devilbiss COMPACT P2-11 Uživatelský manuál (12 strany)

Tabulka s obsahem

Devilbiss COMPACT P2-11 Specifikace (16 strany)

Tabulka s obsahem

Další produkty a příručky pro Stříkací barva DeVilbiss