HP AlphaStation DS20 Guia de Instalação Página 28

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 56
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 27
Linux Installation and Configuration Guide for AlphaServer 28
ECG513/0100
You need to enter these commands, such that the drive reference on the second line needs to refer
to the drive which you installed to:
P00>>>set boot_file
P00>>>set bootdef_dev dka0
P00>>>set boot_osflags 0
At the SRM prompt, you can now boot directly from the hard drive:
P00>>>boot
SuSE Version 6.3 Distribution
Firmware Inspection and Upgrade
After powering up your AlphaServer computer, type the command "show version". Check that
the version string printed is "V5.4-2 May 19 1999 14:25:16" or newer, and that the first letter of
the version string is a "V". If this is not the case, you should upgrade your firmware. Instructions
on how to do this can be found at http://ftp.digital.com/pub/Digital/Alpha/firmware/ along with
the latest firmware images.
System Resource Manager Configuration
There are several pieces of information that you need to configure in the SRM subsystem, as well
as device identifiers that you should make note of, prior to beginning the installation process. The
steps that follow take you through that process.
Power up your system. After several diagnostics are completed, you will be presented an SRM
prompt "P00>>>", as shown here:
256 Meg of system memory
probing hose 1, PCI
bus 0, slot 9 -- ewa -- DE500-AA Network Controller
probing hose 0, PCI
probing PCI-to-ISA bridge, bus 1
bus 0, slot 5, function 1 -- dqa -- Cypress 82C693 IDE
bus 0, slot 5, function 2 -- dqb -- Cypress 82C693 IDE
bus 0, slot 6, function 0 -- pka -- Adaptec AIC-7895
bus 0, slot 6, function 1 -- pkb -- Adaptec AIC-7895
bus 0, slot 7 -- vga -- ELSA GLoria Synergy
os_type: UNIX - console CIPCA driver not started
System Temperature is 30 degrees C
initializing GCT/FRU at 1ec000
COMPAQ AlphaServer DS20E 500 MHz Console V5.5-21, Oct 18 1999 13:33:24
P00>>>
Determine what devices your system has installed. In particular you will need to note your
installation device (a floppy and/or CD-ROM), and your target disk drive. Entering the command
"show devices" as shown below will print out the information about your system:
P00>>>show device
dka0.0.0.6.0 DKA0 COMPAQ BA03611C9B 3B05
dka100.1.0.6.0 DKA100 COMPAQ BB01811C9C 3B05
dka200.2.0.6.0 DKA200 COMPAQ BB01811C9C 3B05
dqa0.0.0.105.0 DQA0 CD-224E 9.5B
dva0.0.0.0.0 DVA0
ewa0.0.0.9.1 EWA0 00-00-F8-01-F5-DA
pka0.7.0.6.0 PKA0 SCSI Bus ID 7
pkb0.7.0.106.0 PKB0 SCSI Bus ID 7
Vista de página 27
1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 55 56

Comentários a estes Manuais

Sem comentários