Hp ProLiant DL320 G3 Server Manual do Utilizador Página 19
- Página / 119
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
19
Server operations
In this section
Powering up the server .................................................................................................................19
Powering down the server ............................................................................................................19
Preparation procedures .................................................................................................................20
Extending the server from the rack...............................................................................................21
Removing the access panel...........................................................................................................21
Installing the access panel ............................................................................................................22
Removing the PCI riser board assembly ......................................................................................22
Installing PCI riser board assembly..............................................................................................23
Removing the hot-plug SATA backplane.....................................................................................24
Removing the fan assembly..........................................................................................................25
Installing the fan assembly ...........................................................................................................26
Powering up the server
To power up the server, press the Power On/Standby button.
Powering down the server
WARNING: To reduce the risk of personal injury, electric
shock, or damage to the equipment, remove the power cord to
remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the
power supply and some internal circuitry remain active until AC
power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to
power down the server.
1. Back up the server data.
2. Shut down the operating system as directed by the operating system
documentation.
- User Guide 1
- Audience assumptions 2
- Contents 3
- Front panel components 7
- Front panel LEDs and buttons 8
- Rear panel components 10
- Rear panel LEDs and buttons 11
- System board components 12
- System maintenance switch 13
- System board LEDs 14
- Internal USB connector 17
- Fan module location 18
- Server operations 19
- Preparation procedures 20
- Removing the access panel 21
- Installing the access panel 22
- Server operations 23 23
- Removing the fan assembly 25
- Installing the fan assembly 26
- Server setup 27
- Rack planning resources 28
- Optimum environment 29
- Temperature requirements 30
- Power requirements 31
- Rack warnings 32
- Installing hardware options 33
- Server setup 35 35
- Registering the server 36
- Introduction 37
- Memory options 37
- DIMM installation guidelines 38
- Installing DIMMs 38
- Hard drive options 39
- Removing a hard drive blank 40
- Hard drive guidelines 40
- Installing a SATA hard drive 40
- Server cabling 47
- SATA cable routing 48
- SCSI cable routing 49
- Configuration tools 51
- HP ROM-Based Setup Utility 53
- Array Configuration Utility 54
- Management tools 56
- Automatic Server Recovery 57
- ROMPaq utility 57
- Erase Utility 59
- Management Agents 60
- HP Systems Insight Manager 60
- Redundant ROM support 61
- Diagnostic tools 63
- Array Diagnostic Utility 64
- HP Insight Diagnostics 64
- Integrated Management Log 64
- Keeping the system current 65
- Resource Paqs 66
- ProLiant Support Packs 66
- Care Pack 67
- Battery replacement 69
- 5. Remove the battery 70
- Troubleshooting 71
- Important safety information 72
- Warnings and cautions 73
- Troubleshooting 75 75
- Symptom information 76
- Service notifications 77
- Loose connections 77
- Diagnostic steps 77
- Start diagnosis flowchart 78
- Troubleshooting 79 79
- General diagnosis flowchart 80
- Troubleshooting 81 81
- Power-on problems flowchart 82
- Troubleshooting 83 83
- POST problems flowchart 85
- OS boot problems flowchart 87
- Troubleshooting 89 89
- Troubleshooting 91 91
- Other information resources 93
- Electrostatic discharge 95
- FCC rating label 98
- Class A equipment 98
- Class B equipment 99
- Modifications 100
- Mouse compliance statement 100
- Japanese notice 102
- BSMI notice 102
- Korean notice A&B 103
- Laser compliance 103
- Battery replacement notice 104
- Server specifications 107
- Specification 108
- Technical support 109
- Customer self repair 110
- Acronyms and abbreviations 111
- Wake-on LAN 115
Manuais e produtos relacionados com Hardware de computador Hp ProLiant DL320 G3 Server
(28 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais