Hp Integrity rx4610 Server Manual do Utilizador

Version 0501 hp server rx4610 User Guide

Chapter 1: Controls, Ports, and Indicators 3Additional Front Panel Controls and Indicators The input and storage devices provide additional front pan

Chapter 10: Configuring the HP Server 93When you select an item from the Config menu, the utility reads the configuration data of that item from th

Chapter 10: Configuring the HP Server 94Fault Resilient Booting (FRB) Setup Fault Resilient Booting (FRB) allows a multiprocessor system to boot in

Chapter 10: Configuring the HP Server 95PEP Actions Enables or disables Platform Event Paging (PEP) actions when an event filter is triggered. PE

Chapter 10: Configuring the HP Server 96EMP Feature Description Access Mode Set the times during system operation when EMP access over the specifi

Chapter 10: Configuring the HP Server 97EMP Feature Description Set Password If set, this password restricts EMP access through the direct serial

Chapter 10: Configuring the HP Server 98DPC/LAN (Direct Platform Control/LAN) Setup The Direct Platform Control (DPC)/ Local Area Network (LAN) set

Chapter 10: Configuring the HP Server 99DPC/LAN Feature Description Set Password If set, this password restricts DPC LAN access. Select the Set P

Chapter 10: Configuring the HP Server 100 2. Immediately begin pressing <F2> repeatedly until you see video. If the server has an Administ

Chapter 10: Configuring the HP Server 101Main Table 10-4 describes the menu items available on the Main screen. Default values appear in brackets.

Chapter 10: Configuring the HP Server 102Advanced Table 10-5 describes the menu items available on the Advanced screen. Five menu items exist on t

Chapter 1: Controls, Ports, and Indicators 4Diskette Floppy Drive The server supports a slimline IDE diskette drive for 1.44 MB and 120 MB media. Th

Chapter 10: Configuring the HP Server 103BIOS Setup Advanced Screen Menu Items Primary Menu Item Sub Menu Items Value Description Parallel Port

Chapter 10: Configuring the HP Server 104BIOS Setup Advanced Screen Menu Items Primary Menu Item Sub Menu Items Value Description Primary IDE Ma

Chapter 10: Configuring the HP Server 105BIOS Setup Advanced Screen Menu Items Primary Menu Item Sub Menu Items Value Description CPU Work Aroun

Chapter 10: Configuring the HP Server 106Security Table 10-6 describes the menu items available on the Security screen. Default values appear in b

Chapter 10: Configuring the HP Server 107Service Boot [Disabled] Enabled Enabling this item will allow you to boot into Service Partition Boot mo

Chapter 10: Configuring the HP Server 108Running the SELViewer Utility Follow these steps to run the SELViewer Utility: 1. Boot to the EFI Shell

Chapter 10: Configuring the HP Server 109Graphical User Interface The SEL Viewer main window is based on a multi-column format. The data is displa

Chapter 10: Configuring the HP Server 110Option Description Open This option allows the user to open the existing SEL file Save As Save As can

Chapter 10: Configuring the HP Server 111Pull-Down Menu – SEL The SEL pull-down menu includes options for reloading SEL entries from the server, cl

Chapter 10: Configuring the HP Server 112General Help This option displays a detailed description on how to use the SEL Viewer. The help window is

Chapter 1: Controls, Ports, and Indicators 5SCSI Hard Drives The server supports up to two hot-swap drive carriers containing standard 1-inch high by

Chapter 10: Configuring the HP Server 113Navigation Use the keystrokes indicated in Table 10-13 to navigate the SDR Viewer Utility’s main window: T

Chapter 10: Configuring the HP Server 114Pull-Down Menu – File The File pull-down menu includes menu items for opening and saving data files. Thes

Chapter 10: Configuring the HP Server 115Menu Selection Description Compact Sensor Record SDR Type 02h Entity Association SDR Type 08h Gen

116 11 Troubleshooting Introduction If you are having problems with installing your HP Server or booting it up, this chapter provides information

Chapter 11: Troubleshooting 117 6. If you suspect a hardware error, follow these steps: a. Log users off the LAN and power down the HP Server.

Chapter 11: Troubleshooting 118 4. Check the processors for bent pins. If the HP Server Powers On but Fails POST (Power-On Self Test) Use this ch

Chapter 11: Troubleshooting 119 vi. Ensure all disk drive power and data cables are securely and properly connected, at the rear of each drive.

Chapter 11: Troubleshooting 120 1. Check the seating of the IDE cables and power cables. 2. Check that the IDE drives are enabled in the BIOS

Chapter 11: Troubleshooting 121HP Server rx4610 Sensor Codes Sensor Type Sensor Number Sensor Name 00 Spare Sensor 09 Spare Sensor 1 14 Sp

Chapter 11: Troubleshooting 122 19 SCSI TERM Volt 11 1A SCSI TERM Volt 12 41 Processor 0 Power Good 42 Processor 1 Power Good 43 Proc

Chapter 1: Controls, Ports, and Indicators 6Power Supplies The chassis can be configured with three to four power supplies. Each power supply has a d

Chapter 11: Troubleshooting 123 52 Upper Memory Board D2D_0 53 Upper Memory Board D2D_1 54 Lower Memory Board D2D_0 55 Lower Memory Boar

Chapter 11: Troubleshooting 124 3F Hot Plug PCI Slot 9 40 Hot Plug PCI Slot 10 23 Watchdog 03 BMC Watchdog C7 OEM C7 2B Proces

Chapter 11: Troubleshooting 125 BIOS Error Codes\Messages The following list defines the BIOS error codes on the HP Server rx4610 server system.

Chapter 11: Troubleshooting 1268103: BIST Failure : Processor in socket M3 8110: Internal error(IERR): Processor in socket M0 8111: Internal

Chapter 11: Troubleshooting 12784FF: System Event Log Full 8C02: ERRORS FOUND IN MEMORY SUBSYSTEM. FAILING ROWS WILL BE MAPPED OUT ON THE NEXT

Chapter 11: Troubleshooting 1288C6F: Error in memory subsystem: Lower Board, DIMM 31 8C70: Error in memory subsystem: Lower Board, DIMM 32 8C71: Er

Chapter 11: Troubleshooting 1298C91: DIMMs mapped out: Lower Board, 1 - 4 8C92: DIMMs mapped out: Lower Board, 9 - 12 8C93: DIMMs mapped out: Lower

Chapter 11: Troubleshooting 130Table 11-1. BMC Beep Codes Code Description 1-5-1-1 FRB failure (processor failure) 1-5-2-1 No processors in

Chapter 11: Troubleshooting 131 Types of Memory Tests The HP Server rx4610 platform memory test is separated into the following three individual te

Chapter 11: Troubleshooting 132Table 11-2. First Row Detection Order Order Row Board DIMM 1 C Upper 5-8 2 D Upper 13-16 3 E Upper 21-24 4 F Upper

Chapter 1: Controls, Ports, and Indicators 7Rear View The ports and connectors at the rear are listed below and shown in Figure 1-6. Figure 1-6 prov

Chapter 11: Troubleshooting 133 2. Clear CMOS via the front panel or via clear CMOS jumper in order to clear previous defective DIMM history.

Chapter 11: Troubleshooting 134“First row test” - displayed on the upper LCD line“0064 MB” - displayed on the lower LCD line“ALL DIMM MAP OUT” - di

Chapter 11: Troubleshooting 135Where ‘n’ refers to the DIMM number. Example: Consider a system that is populated with two rows of 256 MB DIMMS in

Chapter 11: Troubleshooting 136 1. Determine the location of the row of defective DIMMs from the error message or by running the EFI based SELVie

Chapter 11: Troubleshooting 137Upon reset, you will see the following messages on the LCD and the system will halt: “First row test”“0064 MB”“ALL D

Chapter 11: Troubleshooting 138Case 3 The system is populated with more than one row of memory, the first row memory test encounters a SBE (Single

Chapter 11: Troubleshooting 139(in the example it is 5-8). On replacing the DIMMs, make sure the size and HP part number match. 2. Clear CMOS v

Chapter 11: Troubleshooting 140User Notification The BIOS will try to map out defective rows found during base memory test but will end up in an

Chapter 11: Troubleshooting 141counts the memory as the test is being performed. When the test is completed, the number in this line should equal

Chapter 11: Troubleshooting 142A second set of messages will be seen later in the POST, which indicates where the memory test found errors. The se

Chapter 1: Controls, Ports, and Indicators 8Legacy I/O Panel This board contains all legacy I/O connections and plugs into an edge connector on the I

Chapter 11: Troubleshooting 143A second set of messages will be seen later in the POST that indicates where the memory test found errors. The sequ

Chapter 11: Troubleshooting 144Aborting the Memory Test Users are given the option to abort the memory test by pressing the spacebar. The followin

Chapter 11: Troubleshooting 145Setup Dialog The BIOS setup (F2) menu has the following selections: ->Advanced->Chipset Configuration->Memo

Chapter 11: Troubleshooting 1468C59: Error in memory subsystem: Lower Board, DIMM 9 8C5A: Error in memory subsystem: Lower Board, DIMM 10 8C5B: Err

Chapter 11: Troubleshooting 1478C7B: Error in memory subsystem: Upper Board, DIMM 11 8C7C: Error in memory subsystem: Upper Board, DIMM 12 8C7D: Er

Chapter 11: Troubleshooting 1488C9D: DIMMs mapped out: Upper Board, 5 - 8 8C9E: DIMMs mapped out: Upper Board, 13 - 16 8C9F: DIMMs mapped out: Uppe

149 12 Parts Information Exploded View – Hot Swap and Display 2531146 Figure 14. Hot Swap Components

Chapter 12: Parts Information 150Exploded View – Processor/Memory Access 3 Figure 15. Processor/Memory Complex Access

Chapter 12: Parts Information 151Exploded View – Processor/Memory Complex 789101211132829 Figure 16. Processor/Memory Complex

Chapter 12: Parts Information 152

Chapter 1: Controls, Ports, and Indicators 9PCI LEDs Each PCI slot has four indicator LEDs: two on the outside and two on the inside of the system.

Chapter 12: Parts Information 153Exploded View – Server Management Boards Figure 17. Server Management Boards – Exploded View

Chapter 12: Parts Information 154Exploded View – Power Distribution Board and IDE Drives 2324252627 Figure 18. T-Docking Board and IDE Drives

Chapter 12: Parts Information 155Replaceable Parts List The items in this list and the corresponding item numbers in the respective Exploded Views ap

Chapter 12: Parts Information 156 Figure 16. Processor/Memory Complex Item No. Part Description Part Number 7 256MB DIMM 512MB DIMM 1GB DIMM A6168-

Chapter 12: Parts Information 157 Figure 18. Power Distribution Board and IDE Drives Item No. Part Description Part Number 23 Internal SCSI Cable A

158 Appendix A Specifications Introduction This appendix provides the power requirements, operating conditions (environmental requirements), physica

Appendix A: Specifications 159120 VAC 4.6 A 200/208 VAC 3.2 A 220/230 VAC 2.8 A In-rush Current 25 A Output Voltages +48 V +12 V standby Operati

Appendix A: Specifications 160Table A-3. Weight and Dimensions Weight Approx. 150 lbs (68.1 kg.), depending on configuration – excludes keyboard and

Appendix A: Specifications 1614 8 16 32 Display Mode Refresh Rate Hz 8162432816243281624328162432 640 x 480 60 - 200 800 x 600

Appendix A: Specifications 162Pin Signal Pin Signal 7 GND 15 DDCCLK 8 GND Keyboard and Mouse 346521 Figure A-3. Keyboard and Mouse Connectors

Chapter 1: Controls, Ports, and Indicators 10Applying Power to the HP Server Before applying power to the HP Server, verify that the keyboard and mo

Appendix A: Specifications 163Parallel Port Figure A-4. Parallel Port Connector Pinout Table A-8. Parallel Port Connector Pinout Pin Signal Pin

Appendix A: Specifications 164Pin Signal Description 6 DSR Data set ready 7 RTS Request to send 8 CTS Clear to send 9 RIA Ring indication ac

Appendix A: Specifications 165Universal Serial Bus (USB) There are two external USB connectors designated A and B at the back panel. 41 Figure A-6.

Appendix A: Specifications 166SCSI There is one external SCSI connector on the back of the server. Pin 34Pin 68Pin Pin 35 Figure A-7. SCSI Connector

Appendix A: Specifications 167Pin Signal Pin Signal 29 S29 (+REQ) 63 S63(-REQ) 30 S30 (+I/O) 64 S64 (-I/O) 31 S31 (+DB 8) 65 S65 (-DB 8) 32

Appendix A: Specifications 168Pin Signal Pin Signal 20 Keyed 40 GND PCI PCI connectors exist inside the chassis on the I/O Baseboard. Table A-13

Appendix A: Specifications 169Pin Signal Pin Signal Pin Signal Pin Signal A34 FRAME_L A81 GND B34 GND B81 AD45 A35 GND A82 AD44 B35 IRDY

Appendix A: Specifications 170Pin Signal Pin Signal Pin Signal Pin Signal A23 AD26 A70 AD60 B23 AD27 B70 +3.3V A24 GND A71 AD58 B24 AD25

Appendix A: Specifications 171Information on Jumpers The Information on Jumpers section provides an overview of how to change a jumper settings for a

Appendix A: Specifications 172J1E2J2H1J2H2J2H3J2E3J2E2J2E4J9H1 Figure A-9. Processor Baseboard Jumper Locations Jumpers labeled: J2E3 JTAG SELECT1

Chapter 1: Controls, Ports, and Indicators 112. Logoff and exit the operating system. The following prompt appears: Shell> 3. At the Shell>

Appendix A: Specifications 173JTAG Select2 Settings Jumper block J2E4 adds and skips Processor Board components to the JTAG TDI and TDO signal path.

Appendix A: Specifications 174Setting Host Bus Frequencies Jumper blocks J2H1, J2H2, and J2H3 configure the host bus frequency. The settings for all

Appendix A: Specifications 175Processor Host Core Bus Ratio Jumper block J1E2 configures the host-core bus ratio. By default, the bus ration is two

Appendix A: Specifications 176Miscellaneous Jumper Settings Jumper block J2E2 enables server management write protect, configures cache line size, di

Appendix A: Specifications 177Legacy I/O Board Jumpers Jumper blocks exist on the Legacy I/O Board that allow you to perform recovery boot operations

Appendix A: Specifications 178Configuring FWH Programming Jumper block J4A1 allows you to set the FWH programming at 12 Volts. By default, FWH progr

Appendix A: Specifications 179Clearing the CMOS Register Jumper block J7A1 controls whether settings stored in CMOS nonvolatile memory (NVRAM) are re

Appendix A: Specifications 180Jumper diagram labeled: A. Retains System Password (Default Setting) B. Clears the System Password on Reset Jumper bl

Appendix A: Specifications 181I/O Baseboard Jumpers Jumper blocks exist on the OEM I/O Baseboard that allow you to include the BMC in the JTAG chain

Appendix A: Specifications 182Including the BMC in the JTAG Chain Jumper block J8D1 lets you include or exclude the BMC in the JTAG chain. By defaul

12 2 Opening and Closing the HP Server Introduction This chapter describes how to remove and replace the front bezel and the HP Server's main

Appendix A: Specifications 183Power Distribution Board Jumpers (T-Docking) Jumper blocks exist on the Power Distribution Board (T-Docking) that allow

Appendix A: Specifications 184Forcing a Firmware Update and Flashing Bootblock Write Enable Jumper blocks J4E1 and J4E2 allow you force a firmware up

Appendix A: Specifications 185 OFF AC present / Standby output on. DC-to-DC outputs on and okay ON AC present / Standby output on DC-to-DC f

186 B Equipment Log and Configuration Worksheet Equipment Log Use the blank equipment log provided here to record information about your system. Yo

Appendix B: Equipment Log and Configuration Worksheet 187Item Manufacturer Name and Model Number Serial Number Date Installed Hot Plug PCI Slot (7)

188 Index 1 120 mm cooling fans, 17 172 mm fans, 17 172 mm or 120 mm Fans Do Not Operate, 119 5 5.25-inch drive bay size and capacity, 3 A AC distri

Index 189VGA video port, 161 Console Redirection, 106 control panel, 1 LEDs, 1 switch, 1 cooling, 14 cover removing, 14 replacing, 15 cp command, 9

Index 190FRB, 94 front bezel hinge mounting, 12 installing mounting hardware, 12 snap into place, 12 Front Panel Board, 35 Front Panel LCD, 2 Front P

Index 191Legacy I/O Panel, 8 load command, 91 ls command, 91 M Main BIOS Setup Utility, 100 map command, 91 mass storage installation, 25 mass stor

Index 192Power Distribution Board (T-Docking), 78 power down, accelerated, 93 Power Fail LED, 2 Power On/Off, 2 Power on/off button, 99 power pod, 49

ii Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard t

Chapter 2: Opening and Closing the HP Server 13 Figure 2-1. Removing and Replacing the Front Bezel

Index 193server management cable, 78 Server Management Configuration Utility, 92 Set Administrator Password, Security, 106 set command, 91 Set Pass

Index 194

Chapter 2: Opening and Closing the HP Server 14Removing and Replacing the HP Server’s Main Cover The server comes with a removable top cover. Remov

Chapter 2: Opening and Closing the HP Server 15cover in this direction disengages the hooks on both sides of the top cover from the chassis housing.

Chapter 2: Opening and Closing the HP Server 16 Figure 2-3. Replacing the Cover 7. Close the 120 mm fan cover and tighten the thumbscrew. If the

17 3 Installing Fans and Power Supplies Introduction The fans and power supplies used by the HP Server are hot swappable. The HP Server has four 1

Chapter 3: Installing Fans and Power Supplies 18Hot Swapping the 172 mm Fans The four 172 mm cooling fans are mounted in pairs on each side of the c

Chapter 3: Installing Fans and Power Supplies 19Installing the 172 mm Fans To install the 172 mm fan, complete the following procedure: 1. Lift t

Chapter 3: Installing Fans and Power Supplies 20 Figure 3-2. Removing the 120 mm Fans Installing the 120 mm Fans Follow these steps to install a 120

Chapter 3: Installing Fans and Power Supplies 21Hot Swapping Power Supplies The power system contains four 800-watt autoranging power supplies. The

Chapter 3: Installing Fans and Power Supplies 22 Determining Power Supply Status When the amber power supply failure LED on the front of the chassis

iii Contents 1 Controls, Ports, and Indicators ...1 Introduction ...

Chapter 3: Installing Fans and Power Supplies 23Removing a Power Supply To remove a power supply, complete the following procedure: 1. Locate the

Chapter 3: Installing Fans and Power Supplies 24Installing a Power Supply The power supply bay should not be vacant for more than five minutes when s

25 4 Installing Mass Storage Devices Introduction The HP Server comes standard with a DVD and a floppy diskette drive. The internal mass storage ca

Chapter 4: Installing Mass Storage Devices 26 4. PS 5. Other Boot Devices IDE DVD drive Flexible disk drive 6. PCI slot 1 7. PCI slot 2 8.

Chapter 4: Installing Mass Storage Devices 27from the factory. The procedures in this section describe how to determine drive status, remove a fault

Chapter 4: Installing Mass Storage Devices 28 Figure 4-1. Removing a Hard Disk Drive 4. Carefully slide the assembly out of the bay, and place i

Chapter 4: Installing Mass Storage Devices 29 Figure 4-2 Hot Swapping a SCSI Drive 4. Replace the plastic bezel on the front of the server. Installi

Chapter 4: Installing Mass Storage Devices 30 3. Disconnect the drive’s data and power cables from cable adapter PCB at the rear of the drive. 4.

Chapter 4: Installing Mass Storage Devices 31Removing the DVD Drive To remove the DVD drive, complete the following procedure: 1. Observe the safe

Chapter 4: Installing Mass Storage Devices 32 7. Install the top cover as described in “Removing and Replacing the HP Server’s Main Cover” in Chapt

iv Installing the Floppy Disk Drive ... 29 Installing the DVD Drive ...

Chapter 4: Installing Mass Storage Devices 33Installing the Hard Disk Bay To install the Hard Disk Bay, complete the following steps: 1. Turn off

Chapter 4: Installing Mass Storage Devices 34Removing and Installing the SCSI Backplane The SCSI Backplane resides on the back of the Hard Drive Bay.

Chapter 4: Installing Mass Storage Devices 35Installing the Front Panel Board The Front Panel Board displays server information. The module is attac

36 5 Installing Additional Memory Introduction This chapter provides the procedures for opening the Processor/Memory Complex, installing a memory boa

Chapter 5: Installing Additional Memory 37Removing the Processor/Memory Complex The Processor/Memory Complex mounts memory boards to the processor bo

Chapter 5: Installing Additional Memory 38 8. Rotate the two extraction levers on the sides of the module to eject it from the Sideplane board conn

Chapter 5: Installing Additional Memory 39 Figure 5-3. Memory Board DC-DC Converters Removing and Installing Memory Boards Two Memory Boards reside

Chapter 5: Installing Additional Memory 40 9. Place the memory board on a clean ESD-protected surface. Figure 5-4. Memory Boards Installing Memor

Chapter 5: Installing Additional Memory 41 6. Tighten the two captive screws at the end of the extraction handle. 7. Place the two board clamps

Chapter 5: Installing Additional Memory 42Installing and Removing DIMMs The BIOS automatically detects, sizes, and initializes the memory array, depe

v Boot Priority ... 58 Installing Accessory Boards...

Chapter 5: Installing Additional Memory 43DIMM 32DIMM 31DIMM 24DIMM 23DIMM 16DIMM 15DIMM 8DIMM 7DIMM 28DIMM 27DIMM 20DIMM 19DIMM 12DIMM 11DIMM 4DIMM

Chapter 5: Installing Additional Memory 44Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a

Chapter 5: Installing Additional Memory 45 Figure 5-6. Memory Board DC-to-DC Converters Installing the Processor/Memory Complex To replace the Proce

Chapter 6: Installing an Additional Processor 466 Installing an Additional Processor Introduction Each processor is packaged in a Slot M pin array c

Chapter 6: Installing an Additional Processor 47 Figure 6-1. System Board Set Removing the CPU Thermal Dummy CPU thermal dummies must be installed w

Chapter 6: Installing an Additional Processor 48Installing an Additional Processor This section provides the instructions for installing an additiona

Chapter 6: Installing an Additional Processor 49 Figure 6-2. Installing the Microprocessor 10. Place the power pod into position on the Processor

Chapter 6: Installing an Additional Processor 50 11. Place the triple beam into position by lowering it down over the processors/power pod or the C

Chapter 6: Installing an Additional Processor 51Removing a Processor Use this procedure to remove a processor and its heatsink. The heatsink is atta

Chapter 6: Installing an Additional Processor 52Installing a CPU Thermal Dummy CPU thermal dummies must be installed where a processor is absent to p

vi HP Server rx4610 SEL Data Tables ... 120 HP Server rx4610 Sensor Codes ...

Chapter 6: Installing an Additional Processor 53Removing the Processor Baseboard To remove the processor baseboard, complete the following procedure.

Chapter 6: Installing an Additional Processor 54Installing the Board in a System with Three or Four Microprocessors When installing a board that cont

Chapter 6: Installing an Additional Processor 55 Figure 6-7. The Triple Beam 16. Install the processors and power pods into the bottom half of th

Chapter 6: Installing an Additional Processor 56 7. Install the CPU thermal dummies into the bottom half of the Processor/Memory Complex as describ

Chapter 7: Installing Accessory Boards 577 Installing Accessory Boards Introduction The HP Server has ten I/O expansion slots available. PCI slots

Chapter 7: Installing Accessory Boards 58Boot Priority The Server’s boot priority (BIOS search order for a boot drive) should be considered when sele

Chapter 7: Installing Accessory Boards 59the system. The LEDs operate differently depending upon the operating system installed. Please refer to yo

Chapter 7: Installing Accessory Boards 60 Figure 7-2. Open the PCI PHP Mechanism Securing the Board at the Rear of the Chassis 10. If you are add

Chapter 7: Installing Accessory Boards 61Refer to Chapter 1, "Controls, Ports, and Indicators." WARNING The power supply will continue to

Chapter 7: Installing Accessory Boards 62 7. Lift the rear cover to expose the non-hot plug PCI adapter board cover. 8. Loosen the screw that se

vii Index ... 188

Chapter 7: Installing Accessory Boards 63 19. Attach any cables to the PCI adapter board you just installed. 20. Close the rear part of the top

Chapter 7: Installing Accessory Boards 64 11. Press the center of the rocker switch that secures the end of the board nearest the rear of the chass

Chapter 8: Server Management 658 Server Management Boards Introduction The server management features are implemented using three microcontrollers

Chapter 8: Server Management 66• Processor presence monitoring • Speaker ‘Beep’ capability on standby and when system is powered up • Itanium proce

Chapter 8: Server Management 67• Provides a path for management information via SCSI • Retrieves drive fault status, Backplane temperature, and fa

Chapter 8: Server Management 68I/O Baseboard The I/O Baseboard resides in the upper rear of the chassis and plugs into the Sideplane. After removing

Chapter 8: Server Management 69 12. Remove all DC-DC converters from the Sideplane. Figure 8-2. Removing the Sideplane DC-DC Converters 13. L

Chapter 8: Server Management 70 21. Remove the nine screws and the two hex jackscrews that secure the video connector to the I/O Baseboard in order

Chapter 8: Server Management 71Sideplane Board The Sideplane is attached inside the left wall at the rear of the chassis. It receives the I/O Baseb

Chapter 8: Server Management 72 7. Tilt the Sideplane up and out of the chassis. 8. Remove the two retaining screws from the Sideplane to remove

Chapter 1: Controls, Ports, and Indicators 1 1 Controls, Ports, and Indicators Introduction Before operating the Server, familiarize yourself with

Chapter 8: Server Management 73WARNING Make sure that the rack is anchored securely, so it will not tip when the server chassis is extended. 4.

Chapter 8: Server Management 74Legacy I/O Board The Legacy I/O Board is plugged into the I/O Baseboard in the rear of the chassis. It is accessible

Chapter 8: Server Management 75Server Management CableDVD CableFloppy DiskDrive Cable Figure 8-6. Removing Legacy I/O Board 14. Remove both IDE

Chapter 8: Server Management 76 8. Close the plastic latching mechanism that secures the end of the board nearest the front of the chassis. 9.

Chapter 8: Server Management 77Changing the Legacy I/O Board Battery The lithium battery on the Legacy I/O board powers the real-time clock (RTC) fo

Chapter 8: Server Management 78Power Distribution Board (T-Docking) The Power Distribution Board (T-Docking) resides in the upper front half of the c

Chapter 8: Server Management 79 Figure 8-7. Removing the Power Distribution Board (T-Docking)’s Top Bracket 10. Remove the 12 V DC-DC converter

Chapter 8: Server Management 80 Figure 8-8. Removing the AC Distribution Bracket 13. Loosen the six captive thumbscrews securing the Power Distri

Chapter 8: Server Management 81 Figure 8-9. Removing the Hard Drive Bay from the Chassis 16. Disconnect the two 172 mm fan cables from the botto

Chapter 8: Server Management 82 Figure 8-10. Removing the Power Distribution Board (T-Docking) Installing the Power Distribution Board (T-Docking) T

Chapter 1: Controls, Ports, and Indicators 2Table 1-1. Control Panel Switch and Indicators Control / Indicator Description Power On/Off This button

Chapter 8: Server Management 83 12. Install the bracket between the 120 mm fan housing and the AC input bracket. Make sure that the fan cable can

84 9 Connecting the Monitor, Keyboard, and Mouse Introduction The PS/2 compatible keyboard and mouse connectors as well as the connection for the m

Chapter 9 Connecting the Monitor, Keyboard, and Mouse 85NOTE The two USB connectors are reserved for printers, scanners, and external modems, but

Chapter 10: Configuring the HP Server 8610 Configuring the HP Server Introduction This chapter provides instructions for the utilities provided

Chapter 10: Configuring the HP Server 87and allows you to use the utility. For more information on entering and using the utility, refer to “Using

Chapter 10: Configuring the HP Server 88EFI Shell A simple, interactive environment that allows EFI device drivers to be loaded, EFI applications

Chapter 10: Configuring the HP Server 89Table 10-1 describes each menu item in the Boot Maintenance Menu. Table 10-1. Boot Maintenance Menu Option

Chapter 10: Configuring the HP Server 90Option Description Exit Returns control to the EFI Boot Manager main menu. This will display the active b

Chapter 10: Configuring the HP Server 91Command Description endfor Delimiter for loop constructs (scripts only) endif Delimiter for IF THEN const

Chapter 10: Configuring the HP Server 92Server Management Configuration Utility The Server Management Configuration Utility (SM Config) is an EFI-b