HP xw2x220c Guia do Utilizador descarregar pdf (Página 52)

Policy Entries

You can set policy entries by manually editing the .SAM file. These settings must be located in a policy

section of the .SAM file, for example, [Local Area Network] or [saved settings]. These values only

specify the default settings in the UI. Values changed by the User in the UI will take effect.

●

Protocol—integer value, 0, 1, or 3. Specify which protocol to use for connection. RDP is 1, RGS

is 3. A value of 0 (automatic) uses autodetected settings, with a preference of RGS over RDP.

Default is 0.

●

Mute—0 or 1. If 0, audio is enabled for this connection. If 1, audio is disabled. Default is 0.

●

SoundQuality—integer value, 1, 2, or 3. Set to 1 for lowest 3 for highest sound quality. This

value is only supported for RGS connections. Default is 2.

●

SoundStereo—0 or 1. If 1, stereo sound is supported. If 0, mono sound is played. This value is

only supported for RGS connections. Default is 1.

●

BordersEnabled—integer value, 0 or 1. If 1, enables normal Windows borders. 0 = no

borders. This value is only supported for RGS connections. Default is 1.

●

WindowSnapEnabled—integer value, 0 or 1. If 1, allows the session window to “snap” to

edge of screen when moved. This value is only supported for RGS connections. Default is 1.

●

AudioFollowsFocus—integer value, 0 or 1. If 0, sound from all sessions is audible. If 1, only

audible sound is from session that has focus. This value is only supported for RGS connections.

Default is 0.

●

MicrophoneEnabled—integer value, 0 or 1. If 1, analog microphone input from the access

device is sent to RGS sessions. This value is only supported for RGS connections. Ignored by RDP

sessions. This feature requires RGS 5.1.3 or later. Default is 0.

●

KeyRepeatEnabled—integer value, 0 or 1. If 1, disables key repeat suppression normally

required by RGS to keep keys in hot key sequences from repeating when held down. This value is

only supported for RGS connections. Default is 0.

●

MapUSB—integer value, 0 or 1. If 1, allows USB redirection. This value is only supported for

RGS connections. With RGS 5.1.3 or later, you may remap USB devices to a selected session

from the HP SAM Connection Bar. Default is 0.

●

ImageQuality—integer value, 0–100. Sets image quality; 0 = lowest quality, lowest network

bandwidth usage. 100 = highest quality, highest network bandwidth usage. This value is only

supported for RGS connections. Default is 65.

●

Compression—0 or 1. If 1, RDP compression is enabled. This value is only supported for RDP

connections. Default is 1.

●

Wallpaper—0 or 1. If 1, the remote desktop wallpaper is displayed. This value is only

supported for RDP connections. Default is 1.

●

Connbar—0 or 1. If 1, a small bar is displayed at the top of the window. This window allows

the user to minimize during a full screen session. This value is only supported for RDP connections.

Default is 1.

●

FullDrag

—0 or 1. If 1, window contents are shown while a window is dragged. This value is

only supported for RDP connections. Default is 1.

44 Chapter 3 Installation

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 109 110

Comentários a estes Manuais

Sem comentários

HP xw2x220c Guia do Utilizador Página 52

Comentários a estes Manuais

Manuais e produtos relacionados com Software HP xw2x220c