Hp Integrity rx4610 Server Manual do Utilizador descarregar pdf (Página 181)

Appendix A: Specifications

174

Setting Host Bus Frequencies

Jumper blocks J2H1, J2H2, and J2H3 configure the host bus frequency. The settings for all three

jumper blocks combine to yield the single frequency. By default, the frequency is set to 133 MHz.

Figure A-12. Host Bus Frequency Settings

Jumper diagram labeled:

A. 133 MHz (Default Setting)

J2H3

CLKSEL

J2H2

J2H1

1 2 ... 176 177 178 179 180 181 182 183 184 185 186 ... 200 201

User Guide 1
Audience Assumptions 2
Contents 3
Open/Close Button 10
LCD DISPLAY 11
• +48 V 13
• +12 V standby 13
Rear View 14
Legacy I/O Panel 15
Powering-Up the HP Server 17
Powering-Down the HP Server 17
Mounting the Front Bezel 19
Main Cover 21
Replacing the Top Cover 22
Tools and Supplies Needed 24
Removing the 172 mm Fans 25
Hot Swapping the 120 mm Fans 26
Installing the 120 mm Fans 27
If only 3 power supplies 28
Removing a Power Supply 30
Installing a Power Supply 31
Mass Storage Guidelines 32
Tools Required 33
Determining Drive Status 34
Removing a Hard Disk Drive 34
Installing the DVD Drive 37
Removing the Hard Disk Bay 39
Installing the Hard Disk Bay 40
Removing the SCSI Backplane 41
1. Disconnect the cable 42
2. Remove the two screws 42
Removing Memory Boards 46
Installing Memory Boards 47
Installing DIMMs 49
Removing DIMMs 51
Removing a Processor 58
Figure 6-7. The Triple Beam 62
Installing Accessory Boards 65
PCI Hot Plug Slots 68
Non PCI Hot Plug Slots 68
Removing Accessory Boards 70
8 Server Management Boards 72
Hot Swap Controller (HSC) 73
Sideplane cover 75
Remove protective 75
Installing the I/O Baseboard 77
Sideplane Board 78
PCI Hot Plug LED Board 79
Legacy I/O Board 81
Server Management 82
DVD Cable 82
Floppy Disk 82
Drive Cable 82
Chapter 8: Server Management 83
Configuring the HP Server 93
Accelerated Cool Down 100
FRB3 Timeout 101
Using BIOS Setup 106
Using the SELViewer Utility 114
Using the SDR Viewer Utility 119
Server Firmware 122
11 Troubleshooting 123
Introduction 123
Common Installation Problems 123
Chapter 11: Troubleshooting 125
BIOS Error Codes\Messages 132
Beep Codes 136
Table 11-1. BMC Beep Codes 137
Types of Memory Tests 138
User Notification 139
User Action 139
Base Memory Test 141
Error Logging 143
Extended Memory Test 147
Examples 149
Memory Test Duration 150
Aborting the Memory Test 151
Setup Dialog 152
DIMMUTIL 155
12 Parts Information 156
Replaceable Parts List 162
Parts List Identifier 162
Appendix A Specifications 165
Appendix A: Specifications 166
Video Display Modes 167
VGA Video Port 168
Keyboard and Mouse 169
Parallel Port 170
Serial Ports A and B 170
Universal Serial Bus (USB) 172
Figure A-7. SCSI Connector 173
Figure A-8. IDE Connector 174
Information on Jumpers 178
Legacy I/O Board Jumpers 184
J7A1 J7A1 186
I/O Baseboard Jumpers 188
J8D1 J8D1 189
Determining DC-to-DC Status 191
Equipment Log 193
BMC, 129, 130 195
Fan Fail LED, 2 196
Front Panel LCD, 2 197
General Fault LED, 2 197
INIT, 2 197
Index 198
Power Fail LED, 2 199
Power On/Off, 2 199
Reset, 2 199
Speaker, 129 200
System Power LED, 2 200

Comentários a estes Manuais

Sem comentários

Hp Integrity rx4610 Server Manual do Utilizador Página 181

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware de computador Hp Integrity rx4610 Server