Hp Integrity rx4610 Server Manual do Utilizador Página 113
- Página / 201
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 10: Configuring the HP Server
106
Security
Table 10-6 describes the menu items available on the Security screen. Default values appear in
brackets.
Table 10-6. BIOS Setup Security Screen Menu Items
Menu Item Default Value Description
Administrator Password Is [Not Installed]
Installed
The current Administrator
password. To set the
Administrator password,
use the Set Administrator
Password menu item. If a
password was entered, the
field value displays as
Installed.
User Password Is [Not Installed]
Installed
The current user password.
To set the user password,
use the Set User Password
menu item. If a password
was entered, the field value
displays as Installed.
Set Administrator Password N/A Clicking this menu item
displays a dialog box in
which you can define the
Administrator password.
Set User Password N/A Clicking this menu item
displays a dialog box in
which you can define the
User password. Setting a
password in this menu item
will allow you to set up
security features such as
Inactivity Timer, Security
Hot Key, Clear User
Password, Unattended Start
and Video Blanking.
System Management
Table 10-7 describes the menu items available on the System Management screen. Default values
appear in brackets.
Table 10-7. BIOS Setup System Management Screen Menu Items
Menu Item Default Value Description
Console Redirection N/A Selecting this option allows you to
configure for console redirection
- User Guide 1
- Audience Assumptions 2
- Contents 3
- Open/Close Button 10
- LCD DISPLAY 11
- • +48 V 13
- • +12 V standby 13
- Rear View 14
- Legacy I/O Panel 15
- Powering-Up the HP Server 17
- Powering-Down the HP Server 17
- Mounting the Front Bezel 19
- Main Cover 21
- Replacing the Top Cover 22
- Tools and Supplies Needed 24
- Removing the 172 mm Fans 25
- Hot Swapping the 120 mm Fans 26
- Installing the 120 mm Fans 27
- If only 3 power supplies 28
- Removing a Power Supply 30
- Installing a Power Supply 31
- Mass Storage Guidelines 32
- Tools Required 33
- Determining Drive Status 34
- Removing a Hard Disk Drive 34
- Installing the DVD Drive 37
- Removing the Hard Disk Bay 39
- Installing the Hard Disk Bay 40
- Removing the SCSI Backplane 41
- 1. Disconnect the cable 42
- 2. Remove the two screws 42
- Removing Memory Boards 46
- Installing Memory Boards 47
- Installing DIMMs 49
- Removing DIMMs 51
- Removing a Processor 58
- Figure 6-7. The Triple Beam 62
- Installing Accessory Boards 65
- PCI Hot Plug Slots 68
- Non PCI Hot Plug Slots 68
- Removing Accessory Boards 70
- 8 Server Management Boards 72
- Hot Swap Controller (HSC) 73
- Sideplane cover 75
- Remove protective 75
- Installing the I/O Baseboard 77
- Sideplane Board 78
- PCI Hot Plug LED Board 79
- Legacy I/O Board 81
- Server Management 82
- DVD Cable 82
- Floppy Disk 82
- Drive Cable 82
- Chapter 8: Server Management 83
- Configuring the HP Server 93
- Accelerated Cool Down 100
- FRB3 Timeout 101
- Using BIOS Setup 106
- Using the SELViewer Utility 114
- Using the SDR Viewer Utility 119
- Server Firmware 122
- 11 Troubleshooting 123
- Introduction 123
- Common Installation Problems 123
- Chapter 11: Troubleshooting 125
- BIOS Error Codes\Messages 132
- Beep Codes 136
- Table 11-1. BMC Beep Codes 137
- Types of Memory Tests 138
- User Notification 139
- User Action 139
- Base Memory Test 141
- Error Logging 143
- Extended Memory Test 147
- Examples 149
- Memory Test Duration 150
- Aborting the Memory Test 151
- Setup Dialog 152
- DIMMUTIL 155
- 12 Parts Information 156
- Replaceable Parts List 162
- Parts List Identifier 162
- Appendix A Specifications 165
- Appendix A: Specifications 166
- Video Display Modes 167
- VGA Video Port 168
- Keyboard and Mouse 169
- Parallel Port 170
- Serial Ports A and B 170
- Universal Serial Bus (USB) 172
- Figure A-7. SCSI Connector 173
- Figure A-8. IDE Connector 174
- Information on Jumpers 178
- Legacy I/O Board Jumpers 184
- J7A1 J7A1 186
- I/O Baseboard Jumpers 188
- J8D1 J8D1 189
- Determining DC-to-DC Status 191
- Equipment Log 193
- BMC, 129, 130 195
- Fan Fail LED, 2 196
- Front Panel LCD, 2 197
- General Fault LED, 2 197
- INIT, 2 197
- Index 198
- Power Fail LED, 2 199
- Power On/Off, 2 199
- Reset, 2 199
- Speaker, 129 200
- System Power LED, 2 200
Manuais e produtos relacionados com Hardware de computador Hp Integrity rx4610 Server
(144 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais