Hp EVA Array iSCSI Connectivity Option Manual do Utilizador Página 55
- Página / 229
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Table 14 S erial port p in definition
Dongle DB9 pin
number
mpx100/100b RJ–45 pin
number
nl
Description
15
Data carrier detect (DCD)
26
Receive data (RxD)
33
Transmit data (TxD)
4
2&7
Data terminal ready (DTR)
5
4
Signal ground (GND)
6
5
Data set ready (DSR)
71
Request to send (RTS)
88
Clear to send (CTS)
9
N/C
Ring indicator ( RI)
Installation and maintenance
This section describes how to install and con figure the mpx100/100b. It also describes how to update
new firmwareandrecoveradisabledmpx100/100b.
For the mpx100/100b hardware installation, see
“Installing and upgrading EVA iSCSI connectivity” on page 39.
Power requirements
Powerrequirementsforthempx100/100bare0.5Ampat100VACor0.25Aat240VAC.
Environmental conditions
Consider the factors that affect the climate in your facility, such as equipment heat dissipation and
ventilation. The mpx100/100b requires the following operating conditions:
• Operating temperature range: 5 °–40° C (41°–104° F)
• Relative humidity: 15–80%, noncondensing
Connecting the ser ver to the mpx100/100b
You can manage the mpx100/100b us ing the HP StorageWorks mpx Manag er or the CLI. HP
StorageWorks mpx Manager requires an Ethernet connection to the mpx100/100b management port.
The CLI uses either an Ethernet connection or a serial connection. Choose the mpx100/100b management
method, then connect the management server to the mpx100/100b in one of the following ways:
• Indirect Ethernet connection from the management server to the mpx100/100b RJ-45 connector
through an Ethernet switch or hub.
• Direct Ethernet connection from the management server to the mpx100/100b RJ-45 Ethernet
connector.
• Serial port connection from management workstation to the mpx100/100b RS-232 serial por t
connector. This requires a 10/100 Base-T straight cable and a dongle.
Configuring the server
If you plan to use the CLI to configure and manage the mpx100/100b, you must con figure the ser ver
appropriately. This involves either setting the server IP address for Ethernet connections, or configuring
the server's serial port.
EVA iSCSI connectivity user guide
55
- HP StorageWorks 1
- Contents 3
- About t his guide 17
- Document conven 18
- Rack stability 18
- HP technical suppor t 19
- Subscription service 19
- Other HP websites 19
- About this guide 20
- 1OverviewoftheEVAand 21
- Storage System 22
- Hardware support 25
- Software support requirements 26
- Secur ity 28
- Business C opy 28
- 2Configuration rules and 29
- Operating systems supported 30
- Initiator rules 31
- Windows iSCSI In 32
- OpenVMS hardware requirements 33
- Supported featu 36
- HP Command View E 37
- Supported IP network adapters 37
- IP network requirem ents 38
- Adds a second mpx100 40
- Field direct con 42
- Rack mounting the mpx100/100b 43
- Starting the mp 45
- StorageWorks Command View EVA 45
- Figure 12 H 47
- 8. Enter the I 47
- 4Configurin g the mpx 100/100b 49
- Power LED (green) 50
- Heartbeat LED (g reen) 50
- System Fault LED (amber) 50
- Maintenance button 51
- FC ports 52
- Transceivers 53
- Management Eth 54
- Serial port 54
- Installation and maintenance 55
- Setting the server IP address 56
- Configuring the mpx100/100b 58
- Configuring the 60
- (optional) 60
- Configuring the mpx100/100 b 64
- (single-path 68
- Figure 25 Discover targets 69
- (Figure 26) 69
- Assigning device names 79
- Target bindings 80
- Unmounting file systems 81
- -i iscsi 83
- Initiator using the CLI 84
- Accessing iSCSI disks 85
- Configuring TCP/ 90
- IP services 90
- Configuring VL ANs 90
- Configuring target discovery 90
- Starting th e iSCSI Initiator 92
- Stopping the iSCSI Initiator 92
- Overview 95
- The mpx100/100b perspective 96
- 50:05:08:b4:01:01:f6:78 97
- 50:05:08:b4:01:01:f6:7c 97
- Figure 49 Add Features page 101
- Microsoft MPIO 107
- (see Figure 62) 111
- Managing multipathing 113
- MPxIO overview 116
- Setting configu 117
- Verifying confi 119
- Verifying that a 120
- EVA iSCSI Connectivity 121
- Option release notes 121
- Verify mpath-s 122
- Displaying path information 124
- Manual path switching 125
- Disk Arrays 126
- HPDM Multipath restrictions 127
- 7UsingHPCommandViewEVAto 129
- View EVA 131
- Command View EVA 131
- 8 iSCSI Boot from SAN 133
- HP iSCSI 133
- Boot for Wi 133
- QLogic iSCSI Host Bus adapter 134
- QLogic BIOS Readme 135
- 3. Shut down the host 136
- Initiator Upgrade License 137
- Installing t 138
- Upgrade Lic 138
- A Command line interface 141
- Admin command 142
- Beacon command 143
- Date command 143
- Clear command 144
- FRU command 144
- Help command 145
- History comman 147
- Image command 147
- Initiator command 147
- Logout command 148
- LUNmask command 148
- Password command 150
- Ping command 151
- Quit command 151
- Reboot comm and 151
- Reset command 152
- Save command 152
- Set command 152
- Set CHAP comma 153
- Set FC command 153
- Set Features command 154
- Set iSCSI command 154
- Set iSNS command 155
- Set MGMT command 156
- Set NTP command 156
- Set Properties 157
- Set SNMP command 157
- Set System command 158
- Set VLAN comm 158
- Show command 158
- Show Chap command 159
- Show Features command 160
- Show Logs Command 160
- Show LUNinfo 160
- Show Perf command 160
- Show Properties command 161
- Show System command 161
- Show MGMT comma 162
- Show iSCSI command 162
- Show FC command 162
- Show Initiators command 163
- Show iSNS command 164
- Show LUNs command 164
- Show LUN Mask command 165
- Show NTP command 166
- Show SNMP comma 167
- Show Stats command 168
- Show Targets command 171
- Show VLAN comma 172
- Target command 172
- Chassis diag 173
- Power-on self-t 174
- Initiator 175
- Troubleshoo 176
- HP Command View EVA refresh 177
- CLogdata 179
- Fibre Channel driver 180
- Err or log messag 181
- ID Log message Mes 182
- Description 182
- User modules 186
- Fatal log messages 187
- FC driver 189
- Protocol 191
- D Simple Net work Management 191
- Management Information Base 192
- Network port table 193
- FC port table information 195
- Sensor table 197
- Notifications 199
- E Setting up a uthen tication 203
- Setting up authentication 204
- Enabling singl 205
- Enabling bi 209
- F S aving an d restorin g the 213
- G Regul atory compliance and 217
- Regulatory comp 218
- Laser device 218
- European Union notice 219
- BSMI notice 219
- Japanese notice 219
- Batter y repl 220
- Power cords 220
- Japanese power cord statement 221
- Glossary 223
Manuais e produtos relacionados com Acessórios para Computador Hp EVA Array iSCSI Connectivity Option
Acessórios para Computador Hp IO Accelerator for BladeSystem c-Class Manual do Utilizador
(57 páginas)
(57 páginas)
Acessórios para Computador Hp Virtual Connect 1.10Gb-F Ethernet Module for c-Cla Manual do Utilizador
(13 páginas)
(13 páginas)
Acessórios para Computador Hp StoreFront Analytics for VMware Software Licenses Manual do Utilizador
(44 páginas)
(44 páginas)
Acessórios para Computador Hp NC364T PCI Express Quad Port Gigabit Server Adapte Manual do Utilizador
(20 páginas)
(20 páginas)
Acessórios para Computador Hp NC373F PCI-E Multifunction 1000SX Gigabit Server A Manual do Utilizador
(17 páginas)
(17 páginas)
Acessórios para Computador Hp NC370T PCI-X Multifunction Gigabit Server Adapter Manual do Utilizador
(23 páginas)
(23 páginas)
Acessórios para Computador Hp StorageWorks Enterprise File Services WAN Accelera Manual do Utilizador
(194 páginas)
(194 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais