HP Apollo 9000 400t Manual de Serviço Página 269
- Página / 296
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Confi guring the EEPROM C-17
C.4.3 Using the Control Functions
Your Configurable Interfaces menu has three control functions
N store New values
D store Default values
(then cycle SPU power)
A Abort without changes
• N saves all listed interfaces reconfigured values in the EEPROM. You can turn
OFF your system unit, then turn it back ON and the values you configured the
interfaces to are used. Then the self-test runs.
• D exits the Configuration Mode and resets the factory default configurations.
You must cycle system unit power to reconfigure the interfaces to these default
values.
• A causes the Boot ROM to reset and run the self-test without saving any new
interface configurations you may have made. The interfaces’ existing configu
-
rations are used.
If the Boot ROM or EEPROM has problems after you enter N or D, the mode lines
display one of the error messages shown in the following table.
Table C-6. Configuration Mode Exit Error Messages
Command Error Message Meaning and What To Do
N or D
N or D
N or D
A
Too many configuration saves
Can not save new configuration
EEPROM can not save information
(No message should appear)
More than 64,000 saves were tried.
Unlikely to occur.
Something prevented saving the new
configuration. Hardware failure.
Replace CPU board.
EEPROM may not save any or all of
the new configuration information.
Hardware failure. Replace CPU
board.
No error messages should appear
when you abort configuration mode
and reset you system unit.
- Series 400 Workstations 1
- Emissions Regulations 3
- VCCI Class 1 ITE Equipment 4
- VCCI Class 2 ITE Equipment 4
- Preface 7
- Audience 8
- Domain/OS Related Manuals 8
- HP-UX Related Manuals 9
- Documentation Conventions 10
- Contents 11
- Contents xiii 13
- Domain/OS Systems 15
- Contents xvii 17
- Contents xix 19
- Procedures 21
- Chapter 1 23
- 1.1 Introduction 24
- 1-4 Product Overview 26
- 1.2 Physical Configuration 27
- 1-8 Product Overview 30
- 1.5 Introduction 31
- 1.6 Physical Configuration 33
- 1-16 Product Overview 38
- Chapter 2 41
- 2-2 System Controls 42
- System Controls 2-3 43
- 2.2 Monitor Controls 46
- System Controls 2-7 47
- 2-8 System Controls 48
- 2.3 LED Indicator Lights 49
- Chapter 3 51
- 3-4 Theory of Operation 54
- Theory of Operation 3-5 55
- 3-6 Theory of Operation 56
- Theory of Operation 3-7 57
- 3-8 Theory of Operation 58
- 3.2 FRU-Level Operation 59
- Uncorrectable Memory Error 65
- 3-20 Theory of Operation 70
- Chapter 4 71
- Compatible Mode 73
- 4-4 Fault Isolation 74
- Figure 4-1. Main Flowchart 74
- Fault Isolation 4-5 75
- 4-6 Fault Isolation 76
- Fault Isolation 4-7 77
- 4-8 Fault Isolation 78
- Fault Isolation 4-9 79
- 4-10 Fault Isolation 80
- Fault Isolation 4-11 81
- 4-12 Fault Isolation 82
- Fault Isolation 4-13 83
- 4-16 Fault Isolation 86
- 4.3 Mnemonic Debugger Level 87
- 4-22 Fault Isolation 92
- 4.4 The sysboot Program 95
- 4.5 Online Level 96
- Fault Isolation 4-29 99
- 4-30 Fault Isolation 100
- Fault Isolation 4-31 101
- 4.9 Boot ROM Self-Tests 108
- Fault Isolation 4-43 113
- Fault Isolation 4-45 115
- Fault Isolation 4-47 117
- Fault Isolation 4-49 119
- 4.10 Test Mode 122
- CONTINUE AT OWN RISK 123
- RETURN To Continue 123
- Memory Failed at (address) 124
- (W:BBCCDDEE, R:BBCCDDEF) 124
- PARITY BIT ERROR AT (address) 124
- 4-56 Fault Isolation 126
- Fault Isolation 4-57 127
- Part 3 Checkout Procedures 130
- Fault Isolation 4-61 131
- 4-62 Fault Isolation 132
- Fault Isolation 4-67 137
- J001 14 137
- Domain Compatible Mode 139
- Compatible Mode 147
- Chapter 5 149
- 5.3 System Assemblies 150
- 5.5 System Unit Assemblies 172
- (Continued) 227
- Appendix A 235
- A-2 FRU Confi gurations 236
- A-6 FRU Confi gurations 240
- FRU Confi gurations A-7 241
- FRU Confi gurations A-11 245
- Hard Disk Drive 245
- A-12 FRU Confi gurations 246
- Tape Drive 246
- FRU Confi gurations A-13 247
- A-14 FRU Confi gurations 248
- Appendix B 249
- Appendix C 253
- C-2 Confi guring the EEPROM 254
- C.4 I/O Configuration Mode 264
- Configure Mode Failed 265
- Configuration EEPROM Failed 265
- 1 Select Code 9 268
- used select codes are : 268
- 12 14 15 21 268
- C.5 Auto System Select Mode 277
- Appendix D 283
Manuais e produtos relacionados com Barebones PC/estação de trabalho HP Apollo 9000 400t
(24 páginas)
Barebones PC/estação de trabalho HP 8200 - Elite Convertible Minitower PC Especificações Rápidas
(73 páginas)
(73 páginas)
Barebones PC/estação de trabalho HP Dc5850 - Compaq Business Desktop Especificações Rápidas
(54 páginas)
(54 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais